shawn_090

iTrader: (2)

i just got my 1.3r cable today and was going to go do some logging. but im unable to read my rom this is what shows up on ecuflash. is there something im missing? thank

[18:36:20.812] EcuFlash Version 1.43.3172
[18:36:20.812] OS Version Windows XP
[18:36:20.812] Qt Version 4.6.2
[18:36:20.828] 62 memory models read.
[18:36:20.828] scanning for metadata models in C:/Program Files/OpenECU/EcuFlash/rommetadata
[18:36:21.203] 355 ROM metadata models scanned.
[18:36:21.203] checksum module "subarudbw" loaded.
[18:36:21.203] checksum module "mitsucan" loaded.
[18:36:21.203] checksum module "mitsuh8" loaded.
[18:36:21.203] patch module "Subaru CAN Enhanced RAM Parameter Logging" loaded.
[18:36:21.203] patch module "Mitsu CAN RAM Parameter Logging" loaded.
[18:36:21.203] flashing tool "wrx02" loaded.
[18:36:21.203] flashing tool "wrx04" loaded.
[18:36:21.203] flashing tool "sti04" loaded.
[18:36:21.203] flashing tool "sti05" loaded.
[18:36:21.203] flashing tool "mitsukernel" loaded.
[18:36:21.203] flashing tool "mitsukernelocp" loaded.
[18:36:21.203] flashing tool "mitsubootloader" loaded.
[18:36:21.203] flashing tool "shbootmode" loaded.
[18:36:21.218] flashing tool "shaudmode" loaded.
[18:36:21.218] flashing tool "subarucan" loaded.
[18:36:21.218] flashing tool "subarucand" loaded.
[18:36:21.218] flashing tool "mitsucan" loaded.
[18:36:36.671] Using interface OpenPort 1.3 Universal TX2DQts2d4733ff1cf3226428345c86c2666c86f85cf3b4d
[18:36:36.671] interface close
[18:36:36.687] unable to connect to vehicle interface.

shawn_090

iTrader: (2)

Anyone

drifterific

iTrader: (10)

I know it is a stupid question but do you have your key to the on position?

95630706

select ECU= "EFI"?
Device set up =Evo Scan USB cable?
"Mitsubishi" box checked?
Gen3 evo 8/9 selected when reading ROM?

3grst01

iTrader: (9)

Unable to connect to vehicle interface. Either bad cable connection or damaged cable or not sure but might be wrong tactrix cable for your application. I have the openport 2.0 wireless connector with my evo 8 rom and that works. Good luck man.

ecktt

I thinking the same thing.

shawn_090

iTrader: (2)

Ya the key is in the on position. I just woke up so I'm going to try it out again. Is there something I have to set up in ecuflash or no

milford

iTrader: (18)

no you dont need to mess with ecuflash.

shawn_090

iTrader: (2)

I don't understand what your really asking

DFelton

iTrader: (4)

Did you plug both cables? The tactrix and the ecu reader one that plugs in next to it? I had the same problem until I realized they both have to be plugged in to read he rom.

LGshow19

iTrader: (51)

He's walking you through the steps

select ECU= "EFI"?
Device set up =Evo Scan USB cable?
"Mitsubishi" box checked?
Gen3 evo 8/9 selected when reading ROM?

Make sure you select the proper items when you "Read ECU".

shawn_090

iTrader: (2)

Ok I'll try it again. And yes both cables were plugged in

shawn_090

iTrader: (2)

Ok just tried it 3 more times and comes up with the same thing the only thing I can think of is when I first plugged in my cable my computer came up with new hardware found and it had you install it and when it was in the middle of installing it came up with a message something like the windows logo isn't recognize but I pushed continue anyway?????? So I dont know if that has anything to do with it

shawn_090

iTrader: (2)

Still can't Figure it out

95630706

My earlier post as legshow said are the boxes that need to be checked off to read your ECU in the set up dialog. Now I'm thinking you don't have the open port drivers installed?