So what does ign timing as map mean? I have 52da

 

used to be called " disable timing knockdown on light acceleration " set to 0

 

Gotcha,

52d0 would be

timing as map immo/o2 both off then

 

yep that it

 

Try this in your xml..

They may help or may not, these tables show both HEX & Bits.

<!-- *** ECU PERIPHERY *** -->

<table name="Disable/Allow P2_FCA, P3_FDA Bits" category="ECU Periphery" address="101C" type="1D" level="4" scaling="uint8"/>

<table name="ECU Periphery00 (F9A)" category="ECU Periphery" address="f9a" type="3D" level="4" scaling="blobbits">
<table name="HEX" address="f9a" type="X Axis" elements="1" scaling="Hex16">
</table>
<table name="Periphery Bit Number" type="Static Y Axis" flipy="true" elements="16">
<data>bit.15</data>
<data>bit.14</data>
<data>bit.13</data>
<data>bit.12</data>
<data>bit.11</data>
<data>bit.10</data>
<data>bit.9</data>
<data>bit.8</data>
<data>bit.7</data>
<data>bit.6</data>
<data>bit.5</data>
<data>bit.4</data>
<data>bit.3</data>
<data>bit.2</data>
<data>bit.1</data>
<data>bit.0</data>
</table>
</table>

<table name="ECU Periphery0 (FAA)" category="ECU Periphery" address="faa" type="3D" level="4" scaling="blobbits">
<table name="HEX" address="faa" type="X Axis" elements="1" scaling="Hex16">
</table>
<table name="Periphery Bit Number" type="Static Y Axis" flipy="true" elements="16">
<data>bit.15</data>
<data>bit.14 : front o2 sensor heater circuit</data>
<data>bit.13</data>
<data>bit.12</data>
<data>bit.11 : 1 = Disable EGR adv</data>
<data>bit.10 : 0 = Disable Unknown Ign Trim</data>
<data>bit.9 : 0 = Disable warmup Ign Retard</data>
<data>bit.8</data>
<data>bit.7 : Enable High Oct Ign Map Lookup</data>
<data>bit.6 : "Enable Speed Limit Test"</data>
<data>bit.5</data>
<data>bit.4 : 0 = Disable Closed Loop</data>
<data>bit.3 : 0 = disable Immobiliser</data>
<data>bit.2</data>
<data>bit.1 : rear o2</data>
<data>bit.0</data>
</table>
</table>

<table name="ECU Periphery1 (FBA)" category="ECU Periphery" address="fba" type="3D" level="4" scaling="blobbits">
<table name="HEX" address="fba" type="X Axis" elements="1" scaling="Hex16">
</table>
<table name="Periphery Bit Number" type="Static Y Axis" flipy="true" elements="16">
<data>bit.15</data>
<data>bit.14</data>
<data>bit.13</data>
<data>bit.12</data>
<data>bit.11</data>
<data>bit.10</data>
<data>bit.9</data>
<data>bit.8</data>
<data>bit.7</data>
<data>bit.6</data>
<data>bit.5 : 2nd thermo fan table</data>
<data>bit.4</data>
<data>bit.3</data>
<data>bit.2</data>
<data>bit.1</data>
<data>bit.0 : 0 = Disable Lean Spool</data>
</table>
</table>

<table name="ECU Periphery2 (FCA)" category="ECU Periphery" address="fca" type="3D" level="4" scaling="blobbits">
<table name="HEX" address="fca" type="X Axis" elements="1" scaling="Hex16">
</table>
<table name="Periphery Bit Number" type="Static Y Axis" flipy="true" elements="16">
<data>bit.15 : PO443, PO446, PO403, PO243, PO090, P2263</data>
<data>bit.14 : EVAP(PO450-PO453)</data>
<data>bit.13 : EVAP(PO441, PO442)</data>
<data>bit.12</data>
<data>bit.11 : PO031, PO032, PO037, PO038</data>
<data>bit.10 : MAP Sensor(P1400)</data>
<data>bit.9 : 0 = Disable EGR Test(PO401)</data>
<data>bit.8 : 0 = Disable Idle Test(PO506, PO507)</data>
<data>bit.7 : PO170(PO171, PO172)</data>
<data>bit.6 : Front O2(PO134)</data>
<data>bit.5 : 0 = Disable PO300</data>
<data>bit.4 : 0 = Disable PO300</data>
<data>bit.3 : O2(PO132,PO136)</data>
<data>bit.2 : PO133, PO159</data>
<data>bit.1 : PO421(Not In FSM)</data>
<data>bit.0</data>
</table>
</table>

<table name="ECU Periphery3 (FDA)" category="ECU Periphery" address="fda" type="3D" level="4" scaling="blobbits">
<table name="HEX" address="fda" type="X Axis" elements="1" scaling="Hex16">
</table>
<table name="Periphery Bit Number" type="Static Y Axis" flipy="true" elements="16">
<data>bit.15 : CT Below Reg(PO128)</data>
<data>bit.14 : Bat. Backup(P1603)</data>
<data>bit.13</data>
<data>bit.12</data>
<data>bit.11 : PO180-PO183, PO461, P2066(fuel sensors)</data>
<data>bit.10</data>
<data>bit.9</data>
<data>bit.8</data>
<data>bit.7 : PS Pressure(PO551)</data>
<data>bit.6 : Speed Sensor(PO500)</data>
<data>bit.5</data>
<data>bit.4</data>
<data>bit.3</data>
<data>bit.2 : PO234, PO243, P2263</data>
<data>bit.1 : PO510(Not In FSM)</data>
<data>bit.0 : P1715, P1750, Etc.</data>
</table>
</table>

<table name="ECU Periphery4 (FEA)" category="ECU Periphery" address="fea" type="3D" level="4" scaling="blobbits">
<table name="HEX" address="fea" type="X Axis" elements="1" scaling="Hex16">
</table>
<table name="Periphery Bit Number" type="Static Y Axis" flipy="true" elements="16">
<data>bit.15 : Rear O2 No Act(PO140)</data>
<data>bit.14 : MAP vs. BARO(PO069)</data>
<data>bit.13 : IAT Circuit(PO111)</data>
<data>bit.12 : PS Pressure sensor(PO554)</data>
<data>bit.11 : A/C 1 Switch(P1530)</data>
<data>bit.10</data>
<data>bit.9</data>
<data>bit.8 : Clutch Pedal Circuit(PO830)</data>
<data>bit.7 : Fuel Pressure Circuit(PO090)</data>
<data>bit.6</data>
<data>bit.5</data>
<data>bit.4</data>
<data>bit.3</data>
<data>bit.2</data>
<data>bit.1</data>
<data>bit.0</data>
</table>
</table>

<table name="ECU Periphery7 Hex" category="ECU Periphery" address="ffa" type="2D" level="1" scaling="Hex16">
<table name="Y" type="Static Y Axis" elements="8">
<data>0xffa</data>
<data>0xffc</data>
<data>0xffe</data>
<data>0x1000</data>
<data>0x1002</data>
<data>0x1004</data>
<data>0x1006</data>
<data>0x1008</data>
</table>
</table>

 

So is it safe to assume that you simply disable the LTFT in all of your roms and leave them that way? This still has STFT enabled tho as well right?