It is a whole new era in the world of turbochargers! Every name worth mentioning in the turbo universe now offers some kind of billet solution and we want to make sure that you know what options are available to you and I want to help you pick the one that is JUUUUUUUUST right for your needs!

We want to make sure to offer you every option available and to be your NUMBER 1 choice for all of your turbo needs!

Let's kick it off in a BIG way! Check out what we have available for you with Billet Turbos.

Precision Turbo 5557 Billet Turbo

The new 5557E by Precision Turbo offers one of the most widely used turbochargers on the market in a revolutionary Billet Aero design! This turbos is capable of over 450hp without the lag typically associated with this kind of power.

Compressor:
Inducer - 2.165" (55mm)
Exducer - 3.00"

Turbine:
Inducer - 2.555"
Exducer - 2.227"

We have this turbocharger available with a turbine housing to fit just about any setup.

Precision Turbo 5857 Billet Turbo

The PTE 5857 offers huge power in a small package by utilizing revolutionary Aero and Bearing technology. The 58mm, Billet compressor is rated at 605HP. 400-500whp on pump gas a very realistic with this turbocharger.

Compressor:
Inducer - 2.285" (58mm)
Exducer - 3.00"

Turbine:
Inducer - 2.555"
Exducer - 2.227"

Precision Turbo 5862 Billet Turbo

The PTE 5862 offers huge power in a small package. Rated at 480-530 hp on pump gas and 615 on race gas.

Compressor:
Inducer-2.285''
Exducer-3.000''

Turbine:
Inducer-2.795''
Exducer-2.437''

Precision Turbo 6057 Billet Turbo

A great turbo in a smaller package! This is the kind of turbo that can still be squeezed into a T04E compressor cover and make well into 500whp! Rated at 630HP!

Compressor:
Inducer-2.375''
Exducer-3.228''

Turbine:
Inducer-2.555''
Exducer-2.227''

Please be sure to specify turbine housing, compressor cover and bearing selection when ordering.

Precision Turbo 6262 Billet Turbocharger

The 6262 has rapidly become one of the most popular turbochargers in the community! These turbochargers can get you into the 600hp range on pump gas!

Compressor:
Inducer-2.450''
Exducer-3.228''

Turbine Wheel:
Inducer-2.795''
Exducer-2.437''

There are just SOME of the Billet Turbochargers available! We will be updating this, daily!!!

Thank you very much for your time and consideration! PM me for great prices on these Billet GEMS!

 

Forced Performance has really raised the bar in the world of Billet Turbos. Their diverse catalog has Billet Turbos for most all application and power demanding builds. Check out just some of the quality Billet Turbos that we have available to you from our friends at FP!

FP BLACK

The FP BLACK™ for the Mitsubishi Lancer Evolution 4-9 is the most fully evolved stock appearing variant we offer. It features an 82mm HTA™ compressor wheel with a flow rate of 68lb/min with our 84mm Flow Advancement Port™ compressor cover. The turbine side features a large 67mm turbine wheel.
The turbo comes standard with a 25psi wastegate actuator and our Evo Oil Filter Housing Line Kit. You may select a lower pressure actuator if needed, but the unit is intended to operate above 25psi of boost pressure. This turbocharger will produce 500-600whp results readily on well prepared engines.



FP RED


NEW to the FP RED™ for the Evolution IX Line up is our own custom 80mm Flow Advancement Port™ compressor cover. You can now choose the new FP 80mm Flow Advancement Port™cover or stick with the standard 63mm Stock Appearing compressor cover as shown above. The larger inlet configuration helps reduce huffing and surging sounds that are often reported with these larger stock format hybrids when lugging the engine at low RPM and high boost pressure but perhaps even more useful is the way it helps feed the splitter blades of the compressor wheel resulting in increased flow. This larger inlet also increases the volume of the intake air pipe and reduces vacuum at the inlet of the turbo. Additionally the volute of the cover is now exactly tailored to the HTA wheel aero for the best performance possible.

The 80mm inlet Flow Advancement Port™ version can be used with our Intake Air Pipe which is located in the Related Products section at the bottom of the page. The intake is undercover black and designed to replace the stock intake air pipe perfectly allowing the use of the recirculated BOV and the valve cover crankcase vent as in the OEM application. The 80mm Flow Advancement Port™ cover can also be used with standard 3" air intake pipes by utilizing a straight 3" coupler also located in the Related Products section at the bottom of this page.

FP HTA GT3076 Ball Bearing Turbocharger

The FP HTA GT3076R turbocharger is based on the world renowned Garrett GT Ball Bearing structure. This fact assures the highest strength and longest service life possible. At Forced Performance, we have long recognized the precision and excellence in manufacturing found in the full line of Garrett Ball bearings cartridges and turbochargers, and this is exactly why we choose Garrett over others manufacturers when we build our custom application HTA units. The 76mm size HTA wheel has 54.8mm inducer and flows over 57lb/min without dropping efficiency, and works well at pressure ratios as high as 4.5:1 .



FP HTA GT3582R Ball Bearing Turbocharger

The FP HTA GT3582R turbocharger is based on the world renowned Garrett GT Ball Bearing structure. This fact assures the highest strength and longest service life possible. At Forced Performance, we have long recognized the precision and excellence in manufacturing found in the full line of Garrett Ball bearings cartridges and turbochargers, and this is exactly why we choose Garrett over others manufacturers when we build our custom application HTA units. Already have a Garrett GT3582R turbo? Wish it was an HTA™? We can help! For a nominal $600 fee you may send us your complete Garrett GT3582R turbocharger and we will refit it with our 82mm HTA™ compressor wheel and advanced ported shroud cover and perform a CHRA balance after assembly to ensure PERFECT balance and max turbo RPM.