18x9.5 Evo pics
Originally Posted by RS2
What if we cut/roll our fenders ?
Do you think we can go for 18x10 ?
CE28N 18x9.5 what would the best offset be ? What's the lowest offset I can go with those wheels ? Front + Rear w/o rubbing ?
Do you think we can go for 18x10 ?
CE28N 18x9.5 what would the best offset be ? What's the lowest offset I can go with those wheels ? Front + Rear w/o rubbing ?
Originally Posted by lil'evil_evo
I think 9.5 is as far as anyone has went. For the offset check on page 3 your answer is somewhere on that page.
a half inch too big for me. 9/9.5 is big enough 
those this car have stock fenders? you think i can run 255/40/18?
Newbie
Joined: Jul 2003
Posts: 98
Likes: 0
what kind of suspension is everyone running with the 18 x 9 or 18 x 9.5? would stock suspension make it rediciously high? also, if i were to get the 18 x 9.5, would i need different offsets for the front and rear or would +30 offset be sufficient?
sorry, but i have another question,
so if i get 18 x 9.5 and the offset would be somewhere around +28-34 (+22 wont clear?), would i be able to run +22 offset on a 18 x 9 without rubbing?
thanks alot guys this thread has helped me very much
-kevin
sorry, but i have another question,
so if i get 18 x 9.5 and the offset would be somewhere around +28-34 (+22 wont clear?), would i be able to run +22 offset on a 18 x 9 without rubbing?
thanks alot guys this thread has helped me very much
-kevin
I have 18x8.5 Volk TE37s with a 32mm offset or something around there. Im using Hotchkis Springs.
The previous owner the car said he has 245s on there and they rubbed so he put on 235/40/18 tires and they are fine. How is it that all you guys can run 255s and such (and are 255s too much for 8.5 with my offset?
The previous owner the car said he has 245s on there and they rubbed so he put on 235/40/18 tires and they are fine. How is it that all you guys can run 255s and such (and are 255s too much for 8.5 with my offset?
Evolved Member
Joined: Mar 2004
Posts: 1,635
Likes: 3
From: Butt**** Nowhere
Just so everyone knows, the FNO1R-C wheel that 5zigen makes only dishes like lilevos in a 9.5 and 10inch wide size. If you get a 9 or smaller width you get the flat spoke. I'd like to see the 18x9.5 in a 30mm or 25mm offset though. THAT would be flush!
Newbie
Joined: May 2005
Posts: 7
Likes: 0
From: Norco CA
lil evo, bad *** car man, i used to have the same rims on my wrx, 18x8.5.........that was the widest i could have gone, but just to let everyone know, the 5zigens look meaner and meaner if you go wider, the differance between the 8inch, and 9.5 changes the entire look of the rim. have you guys seen the fnor1-c's on any 240sx's? if they have a 10 inch rear they look CRAZY
Newbie
Joined: Jan 2006
Posts: 41
Likes: 0
From: Irvine, CA
Let me see if I have this correct. 18x9.5 with 35mm offset (both front and rear), running 285/30/18 will fit with fender lip cut at the rear (factory ride height)?
http://www.splparts.com/Parts/Univer...en/default.htm
http://www.splparts.com/Parts/Univer...en/default.htm
Originally Posted by Fierysun
Let me see if I have this correct. 18x9.5 with 35mm offset (both front and rear), running 285/30/18 will fit with fender lip cut at the rear (factory ride height)?
http://www.splparts.com/Parts/Univer...en/default.htm
http://www.splparts.com/Parts/Univer...en/default.htm
you may have to rolled and pull the fender a little to fit a 285 series tire.
Cutting is a little more complicated because the rear fender carries a dual wall flange with an adhesive in between. Not impossible, just more difficult. And be sure to have that touch up paint at the ready!
Originally Posted by evodave
that looks sick lil'evil_evo ... i got the 17X9s fno1rc's again with 255 40 17s for racing....but i like the dished look of those 18X9.5s....reminds me of the dish on my 17X9.5 (22et) 57s's with the face two dish....hotness like yours!
Originally Posted by NocturnalEVO
You guys who are using a 9.5" wide wheel, when you cut the wheel ALL the way, do you get rubbing along the inner fender liner?
I got 18x9" wheels with a +31 offset and when I cut the wheel ALL the way, i guess the inner side of the tire rubs against the inner fender.
I'm using 245/40/18 tires, however I wanna move upto 255/40/18 tires or even 255/45/18 tires, because the roads here are crappy and u can feel EVERYTHING.
I got 18x9" wheels with a +31 offset and when I cut the wheel ALL the way, i guess the inner side of the tire rubs against the inner fender.
I'm using 245/40/18 tires, however I wanna move upto 255/40/18 tires or even 255/45/18 tires, because the roads here are crappy and u can feel EVERYTHING.
