NsPyR's EVO !!! China
Thread Starter
Newbie
Joined: May 2010
Posts: 37
Likes: 0
From: China, Kunming
Thread Starter
Newbie
Joined: May 2010
Posts: 37
Likes: 0
From: China, Kunming
Thread Starter
Newbie
Joined: May 2010
Posts: 37
Likes: 0
From: China, Kunming
Just thought i'd update with the correct updated parts list of my car;
Updates 24/10/2010 I am now getting these parts now.... Will update with pics soon...
1) BC 2.3 stroker kit (86mm)
2) BC intake & exhaust valve (+1mm)
3) Cometic gasket 1.4mm
4) Arp head
5) Arp stud
6) Oil pump
7) Water pump
8) Rebuild engine kit
9) Rc 1000cc injectors
10) Main & conrod ACL EVO 9 bearing
11) Custom Port head
12) Balance chamber
13) Remove balance cam
14) Hks oil cooler
15)Ams f1-i intake manifold
16) Boomba 75mm Throtte
17) AMS intake fuel kit
18) AMS upper and lower intercooler and pipes
19) Link G4 xtreme EMS
20) AEM water Injection
21) Sheptrans Ultimate Ratio Stage 2 gearbox
22) Sheptrans Stage 2 T-case and wavetrac LSD
23) ORC triple plate clutch
24) K20A ignition Coil system
25) Link Boost Controller Sensor
26) Polyurathane Motor Mounts
27) Forge Acuator that can withstand 2 bars (dunno if the FP black turbo's stock acuator can take 2 bars)
28) Goodridge Stainless steel braided brake lines
29) Stainless steel Clutch line
My next mods i am thinking is upgrading the rear diff, thinking of getting TRE or Shep Trans to do it, but seems TRE never replies my emails but shep trans customer service is much better !!!
also still deciding if i should change my cams from the BC272 to something more aggressive ?
Dunno how much awhp i will make with this setup and pump gas coz we dont have a 4wd dyno here !!!
Updates 24/10/2010 I am now getting these parts now.... Will update with pics soon...
1) BC 2.3 stroker kit (86mm)
2) BC intake & exhaust valve (+1mm)
3) Cometic gasket 1.4mm
4) Arp head
5) Arp stud
6) Oil pump
7) Water pump
8) Rebuild engine kit
9) Rc 1000cc injectors
10) Main & conrod ACL EVO 9 bearing
11) Custom Port head
12) Balance chamber
13) Remove balance cam
14) Hks oil cooler
15)Ams f1-i intake manifold
16) Boomba 75mm Throtte
17) AMS intake fuel kit
18) AMS upper and lower intercooler and pipes
19) Link G4 xtreme EMS
20) AEM water Injection
21) Sheptrans Ultimate Ratio Stage 2 gearbox
22) Sheptrans Stage 2 T-case and wavetrac LSD
23) ORC triple plate clutch
24) K20A ignition Coil system
25) Link Boost Controller Sensor
26) Polyurathane Motor Mounts
27) Forge Acuator that can withstand 2 bars (dunno if the FP black turbo's stock acuator can take 2 bars)
28) Goodridge Stainless steel braided brake lines
29) Stainless steel Clutch line
My next mods i am thinking is upgrading the rear diff, thinking of getting TRE or Shep Trans to do it, but seems TRE never replies my emails but shep trans customer service is much better !!!
also still deciding if i should change my cams from the BC272 to something more aggressive ?
Dunno how much awhp i will make with this setup and pump gas coz we dont have a 4wd dyno here !!!
Last edited by nspyr; May 22, 2011 at 07:38 PM.
Thread Starter
Newbie
Joined: May 2010
Posts: 37
Likes: 0
From: China, Kunming
I am having a problem ATM, my ex temp are high but my afr is rich... Isn't it supposed to be when your afr are rich your ex temp is low ?
On idle my arf reads 12.2 or richer, and ex temp is 300degrees.... What could be causing this?
On idle my arf reads 12.2 or richer, and ex temp is 300degrees.... What could be causing this?
