The Ultimate Aggressive Wheel Thread... Evo X Style
Well Kids, i finally found a reputable fender roller, or so i'm told. It's a body shop in Eastern PA, by the name of LIP Collision, that does a lot of custom work. Unfortunately, it's about a 2.5-3 hr drive so by the time i get there i may not have anything left of the rear quarter panels. I haven't been driving her too much to keep the damage down. They asked if i was going to leave it and i told them Hellll No, i can't cuz of thy distance. They said it wasnt a problem, just be prepared to hang out for a bit, 3-4 hours or 1-2 hour per corner. At least they dont make it a "rush job".
Also, i've been trying to find SEIBON +10mm Front Fenders. Apparently all these wonderful vendors that advertise best pricing and in stock don't have the fenders. SEIBON has them on Back-Order for over a month now, but due in the end of this month. I've contacted (3) different vendors, that belong to this forum, and all 3 vendors told me they had these IN STOCK. When i reply and tell they i want them, there are all of a sudden sold or were on hold. THEN WHY SAY YOU HAVE THEM IN STOCK!!! F*CKIN TEASES...
this is me, to refresh thy memories...
Also, i've been trying to find SEIBON +10mm Front Fenders. Apparently all these wonderful vendors that advertise best pricing and in stock don't have the fenders. SEIBON has them on Back-Order for over a month now, but due in the end of this month. I've contacted (3) different vendors, that belong to this forum, and all 3 vendors told me they had these IN STOCK. When i reply and tell they i want them, there are all of a sudden sold or were on hold. THEN WHY SAY YOU HAVE THEM IN STOCK!!! F*CKIN TEASES...
this is me, to refresh thy memories...
Newbie
Joined: Nov 2003
Posts: 30
Likes: 0
From: KC Metro Area
Well Kids, i finally found a reputable fender roller, or so i'm told. It's a body shop in Eastern PA, by the name of LIP Collision, that does a lot of custom work. Unfortunately, it's about a 2.5-3 hr drive so by the time i get there i may not have anything left of the rear quarter panels. I haven't been driving her too much to keep the damage down. They asked if i was going to leave it and i told them Hellll No, i can't cuz of thy distance. They said it wasnt a problem, just be prepared to hang out for a bit, 3-4 hours or 1-2 hour per corner. At least they dont make it a "rush job".
Also, i've been trying to find SEIBON +10mm Front Fenders. Apparently all these wonderful vendors that advertise best pricing and in stock don't have the fenders. SEIBON has them on Back-Order for over a month now, but due in the end of this month. I've contacted (3) different vendors, that belong to this forum, and all 3 vendors told me they had these IN STOCK. When i reply and tell they i want them, there are all of a sudden sold or were on hold. THEN WHY SAY YOU HAVE THEM IN STOCK!!! F*CKIN TEASES...
this is me, to refresh thy memories...
Also, i've been trying to find SEIBON +10mm Front Fenders. Apparently all these wonderful vendors that advertise best pricing and in stock don't have the fenders. SEIBON has them on Back-Order for over a month now, but due in the end of this month. I've contacted (3) different vendors, that belong to this forum, and all 3 vendors told me they had these IN STOCK. When i reply and tell they i want them, there are all of a sudden sold or were on hold. THEN WHY SAY YOU HAVE THEM IN STOCK!!! F*CKIN TEASES...
this is me, to refresh thy memories...
Quick question: Is that a dry-carbon trunk lid, or an oem one that isn't painted yet?
-Ben
Well Kids, i finally found a reputable fender roller, or so i'm told. It's a body shop in Eastern PA, by the name of LIP Collision, that does a lot of custom work. Unfortunately, it's about a 2.5-3 hr drive so by the time i get there i may not have anything left of the rear quarter panels. I haven't been driving her too much to keep the damage down. They asked if i was going to leave it and i told them Hellll No, i can't cuz of thy distance. They said it wasnt a problem, just be prepared to hang out for a bit, 3-4 hours or 1-2 hour per corner. At least they dont make it a "rush job".
Also, i've been trying to find SEIBON +10mm Front Fenders. Apparently all these wonderful vendors that advertise best pricing and in stock don't have the fenders. SEIBON has them on Back-Order for over a month now, but due in the end of this month. I've contacted (3) different vendors, that belong to this forum, and all 3 vendors told me they had these IN STOCK. When i reply and tell they i want them, there are all of a sudden sold or were on hold. THEN WHY SAY YOU HAVE THEM IN STOCK!!! F*CKIN TEASES...
Also, i've been trying to find SEIBON +10mm Front Fenders. Apparently all these wonderful vendors that advertise best pricing and in stock don't have the fenders. SEIBON has them on Back-Order for over a month now, but due in the end of this month. I've contacted (3) different vendors, that belong to this forum, and all 3 vendors told me they had these IN STOCK. When i reply and tell they i want them, there are all of a sudden sold or were on hold. THEN WHY SAY YOU HAVE THEM IN STOCK!!! F*CKIN TEASES...
And vendors do that... it's like car salesman who spot deliver or say they have something just to get you in the door.
