Work Emotion Cr Kai 18x9.5 + 38 fitment
#1
Newbie
Thread Starter
Work Emotion Cr Kai 18x9.5 + 38 fitment
Hey guys I had a set of Work Emotion Cr Kai 18x9.5 +38. I tried to fit them on my X 2011 but as I thought they didn't clear the front Brembos. My tires are 245/40r18.. The car is lower with swift spring (1.5 finger gap rear, 3 fingers gap front). None of my fenders are rolled.
I also had a set of 1" spacers. When I put the spacers on it easily clear the front Brembos but my rear tires rub on the fenders.
I know the wheels's offset is no Evo's friendly but I have the wheel and they look great on the car.
If I put 5mm spacers would it clear the front Brembos? I tried 1/4 inch spacers and they seemed to clear them.. Is anybody drive Work Emotion Cr Kai and how did you fit it?
I also had a set of 1" spacers. When I put the spacers on it easily clear the front Brembos but my rear tires rub on the fenders.
I know the wheels's offset is no Evo's friendly but I have the wheel and they look great on the car.
If I put 5mm spacers would it clear the front Brembos? I tried 1/4 inch spacers and they seemed to clear them.. Is anybody drive Work Emotion Cr Kai and how did you fit it?
#2
Newbie
I have a set of WORK Emotion CR Ultimate ("Kiwami") 18x9.5's 20mm offset and the fit is fantastic flush with the fender
As you stated 38mm OS is just too much, and if you add the spacer up front most likely will not work without rolling the finder's. The offset is too much.
Stock wheels are 18x8.5 38mm seeing how you are adding a total of 1 inch with the 9.5's the offest needs to be lower sadly
Check this out, this might help some
https://www.evolutionm.net/forums/ev...ent-chart.html
As you stated 38mm OS is just too much, and if you add the spacer up front most likely will not work without rolling the finder's. The offset is too much.
Stock wheels are 18x8.5 38mm seeing how you are adding a total of 1 inch with the 9.5's the offest needs to be lower sadly
Check this out, this might help some
https://www.evolutionm.net/forums/ev...ent-chart.html
#3
EvoM Guru
iTrader: (1)
You could do 20mm bolt on spacers all the way around and be fine...
#5
Newbie
Thread Starter
If u put 20mm all the way you need to cut your OEM studs to fit them!! It could be an option if you want to run these wheel all year long!!
The option I chose was to buy 8mm hubcentric spacers and to change my OEM studs for ARP extendend wheel studs.. With this set up I had a perfect offset and I could run differents wheels..
The option I chose was to buy 8mm hubcentric spacers and to change my OEM studs for ARP extendend wheel studs.. With this set up I had a perfect offset and I could run differents wheels..
The following users liked this post:
Vmotta1984 (Jun 19, 2019)
#6
Newbie
iTrader: (3)
That's a good looking machine. I just noticed the wheels I have are 5x120....Would that change everything for me?
So I bought 8mm spacers, I'm also ordering the extended studs, I'm keeping my fingers crossed hoping this works!
So I bought 8mm spacers, I'm also ordering the extended studs, I'm keeping my fingers crossed hoping this works!
Last edited by Vmotta1984; Jun 20, 2019 at 02:45 PM.
Thread
Thread Starter
Forum
Replies
Last Post
MR06Evo
Evo Tires / Wheels / Brakes / Suspension
10
May 30, 2007 06:37 AM
TeKiZeRo
For Sale - Wheels / Tires
13
May 29, 2007 07:30 PM
EVIL VIII
Evo Tires / Wheels / Brakes / Suspension
9
Mar 14, 2007 02:45 PM
xLaNcErEvOx
Evo Tires / Wheels / Brakes / Suspension
5
Nov 11, 2006 04:41 PM
A-SPEC
Evo 'For Sale' Wheels / Tires
98
Apr 4, 2006 12:34 PM