Mark this thread as Unsold
feeler, 03 evo 8 with super mods
#1
Evolving Member
Thread Starter
iTrader: (39)
Join Date: Jan 2010
Location: new york
Posts: 133
Likes: 0
Received 0 Likes
on
0 Posts
feeler, 03 evo 8 with super mods
lately im undecided about what cars should i get out of my garage and since my evo is not even in my garage yet i was wondering to see what can i get for it.
note: for the past year and a few months all i have is put massive amount of money into the car and i havent even drove the car yet.
when i bought the evo it had 125k and its the same still cuss when i bought it i took it straight to the shop for some heavy mods.
the car is still in the shop about to come out next week for the break_in procedure so with that beying sed everything is new, no cheap parts.
here r the parts that i could remember so far:
My Evo's mods(ENGINE)
Built 2.0 motor stroker
Carrillo k1 rods
Wiseco hd o ringed pistons
Ams Balance shaft elimination kit
Crower bearings
Arp mainstuds
Arp headstuds
Built cnc machined head
supertech valves
supertech dual valve springs
Ferrea titanium retainers
Ferrea bronze guides
Kelfords 272 cams
Speed-tek custom catch can
nrg radiator panel
(TURBO/INTAKE/EXHAUST/FUEL)
Ams gt35r turbo kit
Ams vsr intake manifold
Ams fuel rail
Ams 3.5 fmic
Boomba tb
ID 1000 cc injectors
Dual walbro 255 pumps
Br dual stage boost controller
Sparch-tek pro cdi/coils
Speed-tek Custom uicp
Speed-tek Custom licp
Tial bov 50mmTial waste gate
44mmFujitsubo rm01a catback exhaust
(POWER/DRIVETRAIN)
Shep built transfer case
Quarter master twin clutch
Awd perfo... Aluminum drive shaft
br lightweight front cross member.
DSS level 5 rear axles
(WHEELS/TIRES/HANDLING)
works cr-Kai 18x9.5 +22
works lugs
Dunlop direzza 255/35/18
Project kicks 10mm spacers (front)
BC BR coilovers
Dba drilled & slotted rotors
Cusco 3 points front tower bar
Cusco 3 points trunk bar
Cusco 23mm adjustable rear sway bar
(INtERIOR)
Complete ssl interior
Cf a pillars
Orbital DD kit
Pioneer headunit
Aem boost gauge
Aem wide band
Aem oil temp
Aem water temp
Evodave ashtray gauge pod
Rexpeed dash pod
Blox shift knob
Evo 9 steering wheel
Evo 9 cf a/c vent panel
Evo 9 mr e-brake handle
Trust gauge over lay
greddy infometer touch
hks type 1 turbo timer
(EXTERIOR)
Evo 9 front bumper
Evo 9 JDM rear bumper
Evo 9 mr headlights
Evo 9 mr taillights
Evo 9 rear spoiler
Rexpeed ralliart cf lip
Rexpeed cf ducts
Rexpeed cf side spats
Rexpeed cf side skirt ext
Rexpeed cf rear bump ext
Rexpeed cf heat shield
Rexpeed roof wing
Evodave wide fender kit
vortex cf rear diffuser
ps: his list is more updated than the 1 in the link, and alot of these parts r not on the car yet but will be by next week or so.
heres a link i had opened to see what people would say about my project:
https://www.evolutionm.net/forums/ev...ths-still.html
i am looking to get 31k obo considering that i am loosing aover 15k at that price and i havent even use it, or if not ill just keep the car and get rid of any of my othr car.
keep in mind that whoever gets this car is basically gettin a brand new evo cuss i have changed just about everything and has not been used yet.
ill add more pics soon.
please keep negative comments elsewhere.
thanx for looking.
trades welcome
note: for the past year and a few months all i have is put massive amount of money into the car and i havent even drove the car yet.
when i bought the evo it had 125k and its the same still cuss when i bought it i took it straight to the shop for some heavy mods.
the car is still in the shop about to come out next week for the break_in procedure so with that beying sed everything is new, no cheap parts.
here r the parts that i could remember so far:
My Evo's mods(ENGINE)
Built 2.0 motor stroker
Carrillo k1 rods
Wiseco hd o ringed pistons
Ams Balance shaft elimination kit
Crower bearings
Arp mainstuds
Arp headstuds
Built cnc machined head
supertech valves
supertech dual valve springs
Ferrea titanium retainers
Ferrea bronze guides
Kelfords 272 cams
Speed-tek custom catch can
nrg radiator panel
(TURBO/INTAKE/EXHAUST/FUEL)
Ams gt35r turbo kit
Ams vsr intake manifold
Ams fuel rail
Ams 3.5 fmic
Boomba tb
ID 1000 cc injectors
Dual walbro 255 pumps
Br dual stage boost controller
Sparch-tek pro cdi/coils
Speed-tek Custom uicp
Speed-tek Custom licp
Tial bov 50mmTial waste gate
44mmFujitsubo rm01a catback exhaust
(POWER/DRIVETRAIN)
Shep built transfer case
Quarter master twin clutch
Awd perfo... Aluminum drive shaft
br lightweight front cross member.
DSS level 5 rear axles
(WHEELS/TIRES/HANDLING)
works cr-Kai 18x9.5 +22
works lugs
Dunlop direzza 255/35/18
Project kicks 10mm spacers (front)
BC BR coilovers
Dba drilled & slotted rotors
Cusco 3 points front tower bar
Cusco 3 points trunk bar
Cusco 23mm adjustable rear sway bar
(INtERIOR)
Complete ssl interior
Cf a pillars
Orbital DD kit
Pioneer headunit
Aem boost gauge
Aem wide band
Aem oil temp
Aem water temp
Evodave ashtray gauge pod
Rexpeed dash pod
Blox shift knob
Evo 9 steering wheel
Evo 9 cf a/c vent panel
Evo 9 mr e-brake handle
Trust gauge over lay
greddy infometer touch
hks type 1 turbo timer
(EXTERIOR)
Evo 9 front bumper
Evo 9 JDM rear bumper
Evo 9 mr headlights
Evo 9 mr taillights
Evo 9 rear spoiler
Rexpeed ralliart cf lip
Rexpeed cf ducts
Rexpeed cf side spats
Rexpeed cf side skirt ext
Rexpeed cf rear bump ext
Rexpeed cf heat shield
Rexpeed roof wing
Evodave wide fender kit
vortex cf rear diffuser
ps: his list is more updated than the 1 in the link, and alot of these parts r not on the car yet but will be by next week or so.
heres a link i had opened to see what people would say about my project:
https://www.evolutionm.net/forums/ev...ths-still.html
i am looking to get 31k obo considering that i am loosing aover 15k at that price and i havent even use it, or if not ill just keep the car and get rid of any of my othr car.
keep in mind that whoever gets this car is basically gettin a brand new evo cuss i have changed just about everything and has not been used yet.
ill add more pics soon.
please keep negative comments elsewhere.
thanx for looking.
trades welcome
Last edited by alanarias22; Feb 18, 2011 at 11:00 PM.
#4
Evolving Member
Thread Starter
iTrader: (39)
Join Date: Jan 2010
Location: new york
Posts: 133
Likes: 0
Received 0 Likes
on
0 Posts
so i got back from a long vacation, i passed by the shop to drop the clutch off, so the car should be out the shop tomo, i snapped a few pics to show what is looking like, i also recorded a video of the first start up and all the new parts before the car is driven in the streets, but i cant upload for some reason.
sorry for the crappy cel pics.
sorry for the crappy cel pics.
#5
Evolving Member
Thread Starter
iTrader: (39)
Join Date: Jan 2010
Location: new york
Posts: 133
Likes: 0
Received 0 Likes
on
0 Posts
many of the parts that r mentioned above r yet not istalled on the car but will come with the car,
reason for me not installing them yet is because the car might go into a full partout if not sold soon.
reason for me not installing them yet is because the car might go into a full partout if not sold soon.
Trending Topics
Thread
Thread Starter
Forum
Replies
Last Post