Jim in Tucson

iTrader: (3)

I didn't think the IX even had an I/C sprayer.

I'm pretty sure it is necessary to add a separate indicator light and switch to do map swapping in the IX. Ask skiracer, he has it in his IX.

In fact, Jack of Trades sells the harness (with light and switch) here.

Evoryder

iTrader: (55)

So i'm getting ready to install the V5 again w/ harness. Does the new V5 have the bug fixed with the load reading in the thousands range vs low hundreds?

Vigman

Just donate $25, thank you very much Tephra for this very great work!
If suggestion admitted: I think it could be great to light the CEL everytime rev limit is reached during valet mod...(For some to scream over the F...valet who "screwed" the car...and in my case to have an option (and justify the problem with the thief) if any (I cross my fingers it'll never happen) car jacking...
Cheers

fixem2

iTrader: (30)

TEphra, I am using the 5.1 version of 96530006 as a replacement on an 05 evo 8. Everything seems to work fine, but around 4k rpms in 2nd or 3rd, during acceleration the CEL will start flashing slowly and continue for a good 3-5 minutes. I even turned the car off and restarted and the flash was still there. This is not knock because I have logged with no knock present. This did not have he same issue when running 96940011.

Any thoughts?

I have changed the turned all features off except CEL KNOCK. I have also changed the Valet RPM to 8k.

I have attached my settings currently on the car, hope this helps.

tephra

iTrader: (6)

what version of ecuflash, post up the endian your put in your XML

fixem2

iTrader: (30)

Ecuflash = 1.30.1095, endian = big

I will change to little and report back. Good call completely missed that. Is Ecuflash 1.35 that much better that I should just upgrade?

tephra

iTrader: (6)

/play family fued sound affect.

1.31 and BELOW endian should be little.

that will fix your flashing time...

report back about the 4000rpm thingy... with logs please

ekizenbe

iTrader: (14)

96420008 any updates??????

tephra

iTrader: (6)

no sorry - flat out with work and other promises at the moment.

actually - the 5.8 thread has 96420011 which you should be ok to upgrade too...

discodino

can someone tell me how to remove or insert pins on an evo 9 ecu harness ,
i know how to on evo 8 harness, but in not sure for evo 9 , thanks guys

Cronic

Ran into this last night while flashing the tephra v5 on 90015 IX rom. This popped up after I changed the value for the valet auto and valet to 0 in the options due to a no start. Might start from scratch all over again to ensure everything, but i'm sure everything was transferred properly. Flashed back to a stock rom for now.

23:55:06.125] written in 1 pulse(s)
[23:55:06.156] kernel write flash buffer addr: 00049000 len: 00000200
[23:55:06.250] kernel write flash buffer addr: 00049200 len: 00000200
[23:55:06.390] kernel write flash buffer addr: 00049400 len: 00000200
[23:55:08.484] readback fail
[23:55:08.515] WARNING: failure in flashing block
[23:55:08.546] kernel write flash buffer addr: 0004A000 len: 00000200
[23:55:08.625] readback mismatch
[23:55:08.640] WARNING: failure in flashing block
[23:55:08.640] kernel write flash buffer addr: 0004B000 len: 00000200
[23:55:08.703] readback mismatch
[23:55:08.718] WARNING: failure in flashing block
[23:55:08.718] kernel write flash buffer addr: 0004C000 len: 00000200
[23:55:08.796] readback mismatch
[23:55:08.796] WARNING: failure in flashing block
[23:55:08.796] kernel write flash buffer addr: 0004D000 len: 00000200
[23:55:08.875] readback mismatch
[23:55:08.890] WARNING: failure in flashing block
[23:55:08.890] kernel write flash buffer addr: 0004E000 len: 00000200
[23:55:08.953] readback mismatch
[23:55:08.968] WARNING: failure in flashing block
[23:55:08.968] kernel write flash buffer addr: 0004F000 len: 00000200
[23:55:09.046] readback mismatch
[23:55:09.078] WARNING: failure in flashing block
[23:55:09.109] kernel flash disable
[23:55:09.140] readback mismatch
[23:55:09.140] verifying result...
[23:55:09.140] comparing ECU flash memory pages to image file
[23:55:09.140] seg start len ecu CRC32 img CRC32 same?
[23:55:09.140] readback mismatch
[23:55:09.140] error reading CRC!
[23:55:09.140] error verify checksums! exiting.
[23:55:09.140] interface close

evoredy

iTrader: (7)

your computer's rom file/hard drive area where rom file is is corrupt, your ecu's memory is corrupt, or you had a usb/com communication event/error.

you probably had the latter. just test write or read from the ecu and try again. verify/check/reseat your cable device and its pins too. also, start from scratch with a newly downloaded rom file (if using Tephra's or the like).

j3llyh34d

I have the exact same symptoms as fixem2, But I also have a permenant CEL - I can't work out why?!

Running V5.1 on 96530006 (UK VIII-FQ300) my original ROM ID was 93660005

I'm using EcuFLASH ver 1.35.1650 with "big" as my endian. I've attached my edited XML file, and the map I've been working with.

I've just donated Dave, thank you for the work you've done - truly inspired

Thanks,

j3llyh34d (Si)

tephra

iTrader: (6)

perm cel = problem, get scantech from aktivematrix and read the code

ill be releasing 5.9 real soon - so you can see if that fixes your problem

ps - where did you send the paypal?

j3llyh34d

Will do re scantech. Think I may have found what I've done.... I've somehow mixed up my XML's and corrupted things. I've been editing the wrong file...... dim wit! The attached 9653006.zip is a fresh XML I've just created, the map.zip is what's currently in but has the aforementioned issues (I guess my mistakes may have corrupted things?) - I'll test later when the other half brings the car back

Just tried sending you a PM .....

Hi Dave,

Sorry, I've upset my PayPal account (I cancelled the wrong direct debit) it's fixed now, but you won't receive my funds until Wednesday.

I have sent a $50USD donation to the link on the first post of this thread (sent from webmaster@j3llyh34d{dot}com)

Thanks,

Si.