TephraMod V7
Nov 3, 2009, 09:17 AM
#871
Registered User
Would these MUT values be different from your V6 rom ? I ask because now my gear does not log correctly in Evoscan (it did in V6). Although it seems the rpm/speed still logs correctly.
Is there a how-to on adding the new XML to Evoscan?
the best way to learn is to play around with some xml files
Nov 3, 2009, 12:02 PM
#872
MUTs should be the same, i have not looked at a V7 rom yet but i dont seen why/how it could change.
there is a video in the ECUflash forum showing "how to tune" it should be there. in general you just copy and paste the xml into the bottom of your rom xml file before "<rom>".
the best way to learn is to play around with some xml files
there is a video in the ECUflash forum showing "how to tune" it should be there. in general you just copy and paste the xml into the bottom of your rom xml file before "<rom>".
the best way to learn is to play around with some xml files
Nov 3, 2009, 02:03 PM
#873
Which model of WB o2 we should use?
The genuine NB o2 has 4 wires connector, I have seen only 5 or 6 wires connector for WB o2 sensor.
I think that AFR Safety is a very good failsafe control for SD. If MAP or MAT sensor is damaged there is a failsafe system to keep all under control.
What do you think about this Dave?
The genuine NB o2 has 4 wires connector, I have seen only 5 or 6 wires connector for WB o2 sensor.
I think that AFR Safety is a very good failsafe control for SD. If MAP or MAT sensor is damaged there is a failsafe system to keep all under control.
What do you think about this Dave?
Nov 3, 2009, 04:17 PM
#874
Evolving Member
iTrader: (8)
Join Date: Nov 2007
Location: San Diego, CA
Posts: 169
Likes: 0
Received 0 Likes
on
0 Posts
I updated the Fuel map, timing map, immobilizer code, injector scaling/voltage to be exactly (or interpolated in the case of fuel and timing maps) what they were in my previously tuned map and when I flash the tephra mod, the car can't hold idle.
It starts, but just dies. (I can keep it going by giving it gas, but takes a fair amount of pressing on the accelerator to get it to stay running). When the car was having problems, it also threw a 'speed sensor malfunction' CEL. The Tephra Mod options I have enabled (value of 1) are 'Flash CEL on Knock' and 'Enable Airflow Calcs.' The rest are zeroed.
I've also changed Periphery2 FCA bit 08 to 0 (D-VO mentioned he was having idling problems so I thought that was worth a shot) and had the same result with the car not being able to idle.
Any thoughts? Thanks in advance for the help.
It starts, but just dies. (I can keep it going by giving it gas, but takes a fair amount of pressing on the accelerator to get it to stay running). When the car was having problems, it also threw a 'speed sensor malfunction' CEL. The Tephra Mod options I have enabled (value of 1) are 'Flash CEL on Knock' and 'Enable Airflow Calcs.' The rest are zeroed.
I've also changed Periphery2 FCA bit 08 to 0 (D-VO mentioned he was having idling problems so I thought that was worth a shot) and had the same result with the car not being able to idle.
Any thoughts? Thanks in advance for the help.
Nov 3, 2009, 04:30 PM
#875
I updated the Fuel map, timing map, immobilizer code, injector scaling/voltage to be exactly (or interpolated in the case of fuel and timing maps) what they were in my previously tuned map and when I flash the tephra mod, the car can't hold idle.
It starts, but just dies. (I can keep it going by giving it gas, but takes a fair amount of pressing on the accelerator to get it to stay running). When the car was having problems, it also threw a 'speed sensor malfunction' CEL. The Tephra Mod options I have enabled (value of 1) are 'Flash CEL on Knock' and 'Enable Airflow Calcs.' The rest are zeroed.
I've also changed Periphery2 FCA bit 08 to 0 (D-VO mentioned he was having idling problems so I thought that was worth a shot) and had the same result with the car not being able to idle.
Any thoughts? Thanks in advance for the help.
It starts, but just dies. (I can keep it going by giving it gas, but takes a fair amount of pressing on the accelerator to get it to stay running). When the car was having problems, it also threw a 'speed sensor malfunction' CEL. The Tephra Mod options I have enabled (value of 1) are 'Flash CEL on Knock' and 'Enable Airflow Calcs.' The rest are zeroed.
I've also changed Periphery2 FCA bit 08 to 0 (D-VO mentioned he was having idling problems so I thought that was worth a shot) and had the same result with the car not being able to idle.
Any thoughts? Thanks in advance for the help.
Nov 3, 2009, 04:51 PM
#876
Evolving Member
iTrader: (8)
Join Date: Nov 2007
Location: San Diego, CA
Posts: 169
Likes: 0
Received 0 Likes
on
0 Posts
I'm not disregarding that this works, but I'm more confused as to why this needs to be performed. What in the tephra map is different that causes the problem with idling?
Nov 3, 2009, 05:16 PM
#877
For EvoScan C:\Program Files\EvoScan\EvoScan v2.6\DataSettings\data is where I have the XML opened to, then I'm lost. Where do I place the XML listed in the 2nd post? Normally, I'd do it right before the <rom> for Ecuflash ROM editing... Sorry for clogging the thread. Is it after the last bit of code for GPS Altitude ?
Last edited by SWOLN; Nov 4, 2009 at 06:19 PM.
Nov 3, 2009, 05:43 PM
#878
I think I remember reading somewhere that someone was having a similar problem where it starting running richer at colder temps. It turned out that his MAT scaling was off (the part that doesn't show in your screenshot). I think one of the threads with the MAT scaling had incorrect values maybe.
Post the entire table for your MAT scaling and I will check against mine after I do some logging.
Post the entire table for your MAT scaling and I will check against mine after I do some logging.
PHP Code:
Voltage Temp (F)
0.102639 150.08
0.112414 145.94
0.12219 141.98
0.131965 138.92
0.14174 136.04
0.156403 132.08
0.180841 125.96
0.200391 122
0.229717 116.96
0.254154 113
0.28348 109.04
0.307918 105.98
0.332356 102.92
0.361681 100.04
0.391007 96.98
0.42522 93.92
0.464321 91.04
0.508309 87.98
0.552297 84.92
0.601173 82.04
0.654936 78.98
0.694037 77
0.733138 75.02
0.777126 73.04
0.826002 71.06
0.874878 69.08
0.923754 66.92
0.977517 64.94
1.03617 62.96
1.09482 60.98
1.15836 59
1.19257 57.92
1.22678 57.02
1.261 55.94
1.29521 55.04
1.33431 53.96
1.36852 53.06
1.40762 51.98
1.44673 51.08
1.48583 50
1.52493 48.92
1.56403 48.02
1.60802 46.94
1.652 46.04
1.69599 44.96
1.73998 44.06
1.78397 42.98
1.83284 42.08
1.87683 41
1.92082 39.92
1.9697 39.02
2.01857 37.94
2.06256 37.04
2.11632 35.96
2.1652 35.06
2.21408 33.98
2.26295 33.08
2.31672 32
2.36559 30.92
2.41935 30.02
2.46823 28.94
2.52199 28.04
2.57576 26.96
2.62952 26.06
2.6784 24.98
2.73216 24.08
2.78592 23
2.8348 21.92
2.88856 21.02
2.94233 19.94
2.9912 19.04
3.04497 17.96
3.09384 17.06
3.14761 15.98
3.19648 15.08
3.24536 14
3.29423 12.92
3.34311 12.02
3.39198 10.94
3.43597 10.04
3.48485 8.96
3.52884 8.06
3.57771 6.98
3.6217 6.08
3.6608 5
3.70479 3.92
3.74878 3.02
3.78788 1.94
3.82209 1.04
3.86119 -0.04
3.90029 -0.94
3.93451 -2.02
3.97361 -2.92
4.00782 -4
4.04203 -5.08
4.07136 -5.98
4.10068 -7.06
4.1349 -7.96
4.16422 -9.04
4.18866 -9.94
4.21799 -11.02
4.24242 -11.92
4.26686 -13
4.2913 -14.08
4.31574 -14.98
4.34018 -16.06
4.35973 -16.96
4.37928 -18.04
4.39883 -18.94
4.41838 -20.02
4.43793 -20.92
4.45748 -22
4.47214 -23.08
4.50147 -25.06
4.53079 -27.04
4.55523 -29.02
4.57967 -31
4.59922 -32.98
4.61877 -34.96
4.63343 -36.94
4.64809 -38.92
Nov 3, 2009, 08:10 PM
#881
I'm not able to display the whole table due to it's size, but copied the values to the table below:
PHP Code:
Voltage Temp (F)
0.102639 150.08
0.112414 145.94
0.12219 141.98
0.131965 138.92
0.14174 136.04
0.156403 132.08
0.180841 125.96
0.200391 122
0.229717 116.96
0.254154 113
0.28348 109.04
0.307918 105.98
0.332356 102.92
0.361681 100.04
0.391007 96.98
0.42522 93.92
0.464321 91.04
0.508309 87.98
0.552297 84.92
0.601173 82.04
0.654936 78.98
0.694037 77
0.733138 75.02
0.777126 73.04
0.826002 71.06
0.874878 69.08
0.923754 66.92
0.977517 64.94
1.03617 62.96
1.09482 60.98
1.15836 59
1.19257 57.92
1.22678 57.02
1.261 55.94
1.29521 55.04
1.33431 53.96
1.36852 53.06
1.40762 51.98
1.44673 51.08
1.48583 50
1.52493 48.92
1.56403 48.02
1.60802 46.94
1.652 46.04
1.69599 44.96
1.73998 44.06
1.78397 42.98
1.83284 42.08
1.87683 41
1.92082 39.92
1.9697 39.02
2.01857 37.94
2.06256 37.04
2.11632 35.96
2.1652 35.06
2.21408 33.98
2.26295 33.08
2.31672 32
2.36559 30.92
2.41935 30.02
2.46823 28.94
2.52199 28.04
2.57576 26.96
2.62952 26.06
2.6784 24.98
2.73216 24.08
2.78592 23
2.8348 21.92
2.88856 21.02
2.94233 19.94
2.9912 19.04
3.04497 17.96
3.09384 17.06
3.14761 15.98
3.19648 15.08
3.24536 14
3.29423 12.92
3.34311 12.02
3.39198 10.94
3.43597 10.04
3.48485 8.96
3.52884 8.06
3.57771 6.98
3.6217 6.08
3.6608 5
3.70479 3.92
3.74878 3.02
3.78788 1.94
3.82209 1.04
3.86119 -0.04
3.90029 -0.94
3.93451 -2.02
3.97361 -2.92
4.00782 -4
4.04203 -5.08
4.07136 -5.98
4.10068 -7.06
4.1349 -7.96
4.16422 -9.04
4.18866 -9.94
4.21799 -11.02
4.24242 -11.92
4.26686 -13
4.2913 -14.08
4.31574 -14.98
4.34018 -16.06
4.35973 -16.96
4.37928 -18.04
4.39883 -18.94
4.41838 -20.02
4.43793 -20.92
4.45748 -22
4.47214 -23.08
4.50147 -25.06
4.53079 -27.04
4.55523 -29.02
4.57967 -31
4.59922 -32.98
4.61877 -34.96
4.63343 -36.94
4.64809 -38.92
Nov 3, 2009, 08:32 PM
#882
If that is the case and you want it in fahrenheit, then you can just copy the values in l2r99gst's live map sd rom mat scaling table in the file at the beginning of this post and paste them in your mat scaling table and you should be ok. That is what i am using right now, i just wanted to be sure though.
Nov 4, 2009, 06:30 AM
#883
If that is the case and you want it in fahrenheit, then you can just copy the values in l2r99gst's live map sd rom mat scaling table in the file at the beginning of this post and paste them in your mat scaling table and you should be ok. That is what i am using right now, i just wanted to be sure though.
I'm going to give the LiveMap a shot, but have to do more reading on how it functions. From what I understand you can write temporary changes to RAM while the car is running and then flash a new ROM image once you're happy w/ your settings. Just have to figure out how to do it and test it out.
