Mapping Evo 6.5 TME
#17
Newbie
Thread Starter
Join Date: Sep 2012
Location: United Kingdom
Posts: 18
Likes: 0
Received 0 Likes
on
0 Posts
Ok, so re-read the thread from Ceddy over on Geekmapped and then sat down with the laptop and did some work today, flashed the TME with the Ralliart files from Ceddy and after checking a few things started the car up.
All is working as expected, so now to setup my LC1 with the laptop and start to do some proper logging and adjustments.
One thing I would like to know is can you replace the standard narrowband lamda with a wideband and configure the stock ECU to us that for closed loop?
All is working as expected, so now to setup my LC1 with the laptop and start to do some proper logging and adjustments.
One thing I would like to know is can you replace the standard narrowband lamda with a wideband and configure the stock ECU to us that for closed loop?
#18
Newbie
Thread Starter
Join Date: Sep 2012
Location: United Kingdom
Posts: 18
Likes: 0
Received 0 Likes
on
0 Posts
Right guys, I have just bought myself a micro SD card so that I can log the car whilst driving around without the laptop connected. Could somebody have a quick look and see if I have created it correctly? Especially the Injector Duty section.
Thanks,
Keith
Thanks,
Keith
#20
Evolved Member
iTrader: (10)
#21
Newbie
Thread Starter
Join Date: Sep 2012
Location: United Kingdom
Posts: 18
Likes: 0
Received 0 Likes
on
0 Posts
Yes I had read that thread, created my own file and just wanted to see if anybody would comment on my config file really.
Also I have noticed that my 1byteload and 2byteload values are way off, how do I find out if I need to make any changes to my MUT table for these values for the TME ecu? I am using Ceddy's xml file. I have read a few threads on here where people have been told to check that MUT41?? has the correct value.
I also seem to be logging different values ignition advance vs ignition map values, and again I have read a few threads but nothing specific to the TME rom.
Anybody got any ideas?
Thanks,
Keith
Also I have noticed that my 1byteload and 2byteload values are way off, how do I find out if I need to make any changes to my MUT table for these values for the TME ecu? I am using Ceddy's xml file. I have read a few threads on here where people have been told to check that MUT41?? has the correct value.
I also seem to be logging different values ignition advance vs ignition map values, and again I have read a few threads but nothing specific to the TME rom.
Anybody got any ideas?
Thanks,
Keith
#23
Newbie
Thread Starter
Join Date: Sep 2012
Location: United Kingdom
Posts: 18
Likes: 0
Received 0 Likes
on
0 Posts
#25
Newbie
Thread Starter
Join Date: Sep 2012
Location: United Kingdom
Posts: 18
Likes: 0
Received 0 Likes
on
0 Posts
I can upload a log file and my version of the xml if you like? Only just starting out with this so may not have everything sorted yet as I am just logging and making small changes at the moment. Running on 99 RON fuel here in the UK.
Keith
#29
Newbie
Thread Starter
Join Date: Sep 2012
Location: United Kingdom
Posts: 18
Likes: 0
Received 0 Likes
on
0 Posts
Thanks for that, I look forward to your reply.
I don't suppose you have any ignition maps that I could look at from cars running 98-99 Octane fuel?
Keith
I don't suppose you have any ignition maps that I could look at from cars running 98-99 Octane fuel?
Keith