Current build power output estimate - EvolutionM - Mitsubishi Lancer and Lancer Evolution Community

Notices
Evo Engine / Turbo / Drivetrain Everything from engine management to the best clutch and flywheel.

Current build power output estimate

Reply

 
 
 
Old Jun 19, 2018, 12:58 PM
  #1  
Evolving Member
Thread Starter
iTrader: (1)
 
blackline's Avatar
 
Join Date: Sep 2017
Location: NYC
Posts: 207
Thanked 6 Times in 6 Posts
Current build power output estimate

Hey, So my build is complete and I'm wondering that will be my power output on a heart breaker dyno.

Specs: 2.0L, 93oct

Head:
  • Street ported head
  • CB Ported Intake manifold
  • FB 70mm TB
  • AMS Fuel rail
  • PTE 1000cc
  • GSC S2
  • Manley springs/retainers
  • STD valve size
Block:
  • 85.5MM Wiseco HD
  • Manley TT rods
  • Manley Crank
Turbo:
  • BBK Full Ported
  • Ported Exhaust Manifold
  • Megan O2, DP, catback
  • ETS SD 3in intake
MISC:
  • Converted to SD
  • ETS LICP and Short route with Tial Q
  • STM 3 port catch can
  • Walbro 450
  • ACT Extreme clutch
  • Jacks TCASE and Gearbox
blackline is offline  
Reply With Quote
Old Jun 19, 2018, 11:36 PM
  #2  
Evolved Member
iTrader: (23)
 
deylag's Avatar
 
Join Date: Jul 2010
Location: Milpitas, CA
Posts: 1,204
Thanked 36 Times in 31 Posts
Probably 400-430 whp.
deylag is online now  
Reply With Quote
Old Jun 20, 2018, 10:29 AM
  #3  
Evolving Member
Thread Starter
iTrader: (1)
 
blackline's Avatar
 
Join Date: Sep 2017
Location: NYC
Posts: 207
Thanked 6 Times in 6 Posts
thanks
blackline is offline  
Reply With Quote
Old Jun 20, 2018, 10:40 AM
  #4  
EvoM Super Moderator
iTrader: (3)
 
MinusPrevious's Avatar
 
Join Date: May 2008
Location: So.Cal
Posts: 4,544
Thanked 551 Times in 526 Posts
What gas? What PSI?

Heart breaker = Mustang
MinusPrevious is offline  
Reply With Quote
Old Jun 20, 2018, 11:11 AM
  #5  
Evolved Member
iTrader: (1)
 
2006EvoIXer's Avatar
 
Join Date: Jul 2012
Location: California
Posts: 2,001
Thanked 86 Times in 84 Posts
I assume those Wiseco pistons are 9.0 CR?
With 93 octane, I would guess 410whp
2006EvoIXer is offline  
Reply With Quote
Old Jun 20, 2018, 11:29 AM
  #6  
Evolving Member
Thread Starter
iTrader: (1)
 
blackline's Avatar
 
Join Date: Sep 2017
Location: NYC
Posts: 207
Thanked 6 Times in 6 Posts
It's 9:1 compression and I'll be using 93 oct. I would like to hit 30psi on the BBK but only seen 1 other person hitting that boost level on pump.
blackline is offline  
Reply With Quote
Old Jun 20, 2018, 11:35 AM
  #7  
Evolved Member
iTrader: (5)
 
whtrice's Avatar
 
Join Date: Jun 2006
Location: Sacramento
Posts: 660
Thanked 6 Times in 6 Posts
Originally Posted by 2006EvoIXer View Post
I assume those Wiseco pistons are 9.0 CR?
With 93 octane, I would guess 410whp
That was my guess too if everything falls inline. Rocking 400 whp running 93 oct on a low reading MD has been a rare bird but with
a good SD tune I guess is possible. With E-85 ~ 450- 460
whtrice is offline  
Reply With Quote
The Following User Says Thank You to whtrice For This Useful Post:
2006EvoIXer (Jun 20, 2018)
Old Jun 20, 2018, 11:35 AM
  #8  
Evolved Member
iTrader: (1)
 
2006EvoIXer's Avatar
 
Join Date: Jul 2012
Location: California
Posts: 2,001
Thanked 86 Times in 84 Posts
Originally Posted by blackline View Post
It's 9:1 compression and I'll be using 93 oct. I would like to hit 30psi on the BBK but only seen 1 other person hitting that boost level on pump.
30 psi is a lot to ask for 93. Even with a built engine, that's not much wiggle room for safety. If you BBK is like my 71HTA, if it can boost to 30psi, it will likely be more heat where you won't gain any power. And with more heat, 93 may be a problem.

Last edited by 2006EvoIXer; Jun 20, 2018 at 11:42 AM.
2006EvoIXer is offline  
Reply With Quote
The Following User Says Thank You to 2006EvoIXer For This Useful Post:
Abacus (Jun 20, 2018)
Old Jun 20, 2018, 11:38 AM
  #9  
Evolved Member
iTrader: (1)
 
2006EvoIXer's Avatar
 
Join Date: Jul 2012
Location: California
Posts: 2,001
Thanked 86 Times in 84 Posts
Originally Posted by whtrice View Post
That was my guess too if everything falls inline. Rocking 400 whp running 93 oct on a low reading MD has been a rare bird but with
a good SD tune I guess is possible. With E-85 ~ 450- 460
I guessed 410 because 91 only gets me 380.
depending on dyno, it will be close:
2006EvoIXer is offline  
Reply With Quote
Old Jun 20, 2018, 02:01 PM
  #10  
Evolving Member
Thread Starter
iTrader: (1)
 
blackline's Avatar
 
Join Date: Sep 2017
Location: NYC
Posts: 207
Thanked 6 Times in 6 Posts
I'll report back on or after July 5th(dyno day) with final numbers and sheet.
blackline is offline  
Reply With Quote
The Following User Says Thank You to blackline For This Useful Post:
2006EvoIXer (Jun 20, 2018)
 
 
 


Thread Tools
Search this Thread

Contact Us Archive Advertising Cookie Policy Privacy Statement Terms of Service

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.