Good widebands?

Reply Subscribe

Thread Tools

Search this Thread

Sep 27, 2009 | 01:29 PM

#76

ilikeppie

Evolving Member

iTrader: (24)

Joined: Dec 2008

Posts: 407

Likes: 0

From: Fort Collins, Colorado

i vote aem, i am about to order mine i have not heard anything bad about it

Sep 27, 2009 | 03:55 PM

#77

funks

Evolving Member

iTrader: (4)

Joined: Jul 2007

Posts: 488

Likes: 0

Quote:

Originally Posted by mrubino83

^^^ Just ordered the same piece for my prosport oil pressure gauge.

You gonna be tuning your car w/ that prosport wideband? Are you gonna be hooking up the voltage output to the rear O2's ADC? Otherwise, it won't work with EvoSCAN.

Sep 27, 2009 | 05:06 PM

#78

hotstix

Evolving Member

iTrader: (3)

Joined: Mar 2005

Posts: 368

Likes: 1

From: So. Cal

Quote:

Originally Posted by funks

You gonna be tuning your car w/ that prosport wideband? Are you gonna be hooking up the voltage output to the rear O2's ADC? Otherwise, it won't work with EvoSCAN.

Im not gonna be doing any self tuning. This is just to moniter AFRs and make sure they stay where they should be.

Oct 3, 2009 | 06:03 PM

#79

funks

Evolving Member

iTrader: (4)

Joined: Jul 2007

Posts: 488

Likes: 0

In regards to PLX users, I wrote an EVOXLogger (based off Tephra's Command Line Mode23 logger - thanks Tephra!) that works with the PLX and gives us a tuning solution until EvoScan incorporates PLX iMFD support.

Quote:

Originally Posted by Funks

The MODE 23 EVOXLogger w/ Wideband based off Tephra's is alive. I'd like to thank Tephra for sharing the power of his source :]

It's not a straight C program anymore (now C++/CLI ), so it requires the .NET framework version 3.5 SP1

Wideband Currently Supported
"PLX"
"LM1" <-- needs testing..
"LC1" <-- needs testing..
"ZT2" <-- needs testing..
"AEM" <-- needs testing..

Monitors get configured as follows via file "monitors.config"

Code:

#
# Name:Source:HexAddress:ReturnBytes:RPNFormula:Priority
# 1) Make sure there are NO SPACES (including @ end)
# 2) Make sure your formula is correct - "x" is the value returned from the car.
#
TPS:OP2:0x8086F9:1:x,32,-,129,*,255,/:1
2ByteRPM:OP2:0x808746:2:x,3.90625,*:1
LoadFuel:OP2:0x80876E:2:x,10,*,32,/:1
LoadMivec:OP2:0x808774:2:x,10,*,32,/:1
TimingAdv:OP2:0x808A07:1:x,20,-:1
KnockSum:OP2:0x808A4B:1:x:1
PSIG:OP2:0x80871A:2:x,4,/,0.19347,*,14.5,-:1
WideBandAF:WB:0x000000:0:x:1

The wideband stuff like this via file "wb.config"

Code:

#
# Type:COMPORT:TestMode
#
PLX:COM4:false

When you run the "evoxlogger.exe" it automatically creates a log file in the relative "logs" folder..

The autogenerated filename is generated with the following format - example: "EVOXLoggerDataLog-2009_10_01-22_58.csv"

If you run it as such "evoxlogger.exe C:\temp\mylog.csv" then it writes to the file file path passed in..

Last edited by funks; Oct 12, 2009 at 11:05 PM.

Nov 4, 2009 | 06:29 AM

#80

shh!! sleeping

Evolving Member

iTrader: (7)

Joined: Dec 2008

Posts: 308

Likes: 0

From: LI

This question was posted earlier in the thread but no one seamed to answer... but any feedback on the NGK AFX Wideband ? Does it work with EvoScan? Any + or - from any one who has installed or tuned with it?

I've been looking for a wideband with a display, but i do not want to run a gauge cuz... well... im OCD and Defi doesnt have a wideband gauge and all my gauges have to be the same... the AFX had a red digital readout and its pretty small at that, so i was going to install it where the clock is on the dash just above my Defi 3 gauge setup where the stock radio was... i know it look sick... but its got to be functional and worth my time...

Feedback on the AFX???? anyone???

Nov 11, 2009 | 03:34 PM

#81

JimGVT

Evolving Member

iTrader: (6)

Joined: May 2009

Posts: 251

Likes: 8

From: Vermont

For those of you using the Innovate LC-1, did you replace the factory O2 sensor and then use the narrowband output from the LC-1 to simulate the narrowband to the ECU? If so, did you run into any issues? Thanks.

Nov 11, 2009 | 03:46 PM

#82

EVO_MERLE

Evolving Member

Joined: May 2008

Posts: 144

Likes: 0

From: Pensacola, FL / Norfolk, VA

be careful that sandwich plate puts your oil filter dangerously low to the ground and can get hit or punctured. You can tap for oil pressure on the side of your oil sending unit.

As far as wide bands go i wanted the pro sport as well but found a LC-1 for $75 used and could not turn it down.

Nov 11, 2009 | 03:55 PM

#83

Zeitronix

Evolving Member

iTrader: (2)

Joined: Nov 2005

Posts: 327

Likes: 0

Used LC-1? Hope it works!

Nov 11, 2009 | 03:57 PM

#84

EVO_MERLE

Evolving Member

Joined: May 2008

Posts: 144

Likes: 0

From: Pensacola, FL / Norfolk, VA

works great i was there when we took it out of my friends car and then we put it in mine. Did not get it from the internet or Ebay. LOL

Nov 11, 2009 | 04:21 PM

#85

Zeitronix

Evolving Member

iTrader: (2)

Joined: Nov 2005

Posts: 327

Likes: 0

The only way to do it.

Nov 11, 2009 | 05:56 PM

#86

Chef-j

Evolved Member

iTrader: (16)

Joined: Nov 2009

Posts: 951

Likes: 7

From: Dallas, TX

Anyone have try haltech wideband on Evo? I tried this wideband on other vehicle, it works great.

http://www.injectedperformance.com/e....aspx?ID=10520

Nov 11, 2009 | 06:31 PM

#87

geezevox

Evolving Member

iTrader: (4)

Joined: Jan 2009

Posts: 132

Likes: 0

From: Waldorf, MD

Quote:

Originally Posted by mrubino83

Just ordered my Pro-sport Wideband. I'll post a review once its installed.

http://prosportgauges.com/wideband-a...ratio-kit.aspx

Anybody have any experience with this gauge??

I have the prosport wideband and I love it. It works great and the company is great about any problems (mine came with a small dent on the housing and they replaced it-no charge). Also, I compared the gauge readings to my tuner's dyno readings while my car was being tuned, and it was within a tenth at all times.