Mark this thread as Unsold
Exedy Hd Twin Plate Ceramatellic Clutch
Feb 15, 2008, 05:05 PM
#1
Evolving Member
Thread Starter
iTrader: (1)
Join Date: Feb 2007
Location: Denver, CO
Posts: 105
Likes: 0
Received 0 Likes
on
0 Posts
Exedy Hd Twin Plate Ceramatellic Clutch
SOLD SOLD SOLD
I have a new EXEDY HD TWIN PLATE CERAMATELLIC CLUTCH plus CHROME MOLY FLYWHEEL (part# CM06H, kit# MM022HD) for sale that I had in my Evo IX for less than a thousand miles, which were all break-in miles. No launches, no racing, and no going fast. The clutch also has a brand new factory throw-out bearing. I believe this clutch fits the Evo VIII as well.
Check this link for the full write-up on why I'm selling.
http://denver.craigslist.org/pts/575442645.html
EDIT: I've had a lot of interest, but when it comes down to it, people don't want to take the chance on a clutch that's been used. This is a perfectly good clutch!!!!! I sent it in to the pros at Exedy to inspect it for any possible damage and they said the clutch was in perfect condition and the disc faces were not even worn .05 millimeters!!!!! I have a report showing the clutch is good from Exedy. The only reason I took it out of my car in the first place was because the flat spring that helps disengage the clutch was installed in the wrong position. No damage, just needed to re-adjust the flat spring to the correct position!!!!! This clutch is ready to go!!!!!! If you can't trust the report from Exedy, who can you trust??????
I have a new EXEDY HD TWIN PLATE CERAMATELLIC CLUTCH plus CHROME MOLY FLYWHEEL (part# CM06H, kit# MM022HD) for sale that I had in my Evo IX for less than a thousand miles, which were all break-in miles. No launches, no racing, and no going fast. The clutch also has a brand new factory throw-out bearing. I believe this clutch fits the Evo VIII as well.
Check this link for the full write-up on why I'm selling.http://denver.craigslist.org/pts/575442645.html
EDIT: I've had a lot of interest, but when it comes down to it, people don't want to take the chance on a clutch that's been used. This is a perfectly good clutch!!!!! I sent it in to the pros at Exedy to inspect it for any possible damage and they said the clutch was in perfect condition and the disc faces were not even worn .05 millimeters!!!!! I have a report showing the clutch is good from Exedy. The only reason I took it out of my car in the first place was because the flat spring that helps disengage the clutch was installed in the wrong position. No damage, just needed to re-adjust the flat spring to the correct position!!!!! This clutch is ready to go!!!!!! If you can't trust the report from Exedy, who can you trust??????
Last edited by Wicked White; Feb 22, 2008 at 02:22 PM. Reason: SOLD
Feb 15, 2008, 06:02 PM
#2
Evolved Member
iTrader: (64)
Join Date: Jan 2007
Location: Florida
Posts: 3,377
Likes: 0
Received 0 Likes
on
0 Posts
I thought you said it was new? so is it new or used?
I have a new EXEDY HD TWIN PLATE CERAMATELLIC CLUTCH plus CHROME MOLY FLYWHEEL (part# CM06H, kit# MM022HD) for sale that I had in my Evo IX for a few hundred miles. The clutch also has a brand new factory throw-out bearing. I believe this clutch fits the Evo VIII as well. Check this link for full write-up on why I'm selling.
http://denver.craigslist.org/pts/575442645.html
Check this link for full write-up on why I'm selling.http://denver.craigslist.org/pts/575442645.html
Feb 15, 2008, 07:15 PM
#3
Evolving Member
Thread Starter
iTrader: (1)
Join Date: Feb 2007
Location: Denver, CO
Posts: 105
Likes: 0
Received 0 Likes
on
0 Posts
Sorry to confuse. The clutch was installed once, however I consider less than a thousand miles on a heavy duty clutch like this basically brand new. I was still in the break-in period for this clutch, so I did no racing, no launches, and no going fast. I barely even used it and could immediately tell it was installed wrong. The face of a brand new Exedy disc is 4mm thick. The two faces on this clutch were measured by Exedy at 3.95mm and 3.98mm.
Last edited by Wicked White; Feb 21, 2008 at 09:43 PM.
Feb 16, 2008, 10:24 AM
#6
Evolving Member
Thread Starter
iTrader: (1)
Join Date: Feb 2007
Location: Denver, CO
Posts: 105
Likes: 0
Received 0 Likes
on
0 Posts
Well, I've had some definite interest, but guys, I thought you'd jump at this offer!!! You have the chance of owning one of the best performing street clutches ever made for a bargain, and all because of the sucky ordeal I went through.
