MIVEC tuning
#796
Thanks mrfred. I'm currently completely stock everything apart from FIC 1150 injectors, modified Wally 255 and a 3" DP with 3-port EBC. So basically I'll keep the MIVEC map as it is once the new exhaust is in, thanks.
A bit off topic, but since it will flow more, what is the maps that I need to restrict first or all of them? To a novice like me it would sound rather reasonable to only put in a more conservative waste gate duty cycle and keep everything else as is. Thoughts?
A bit off topic, but since it will flow more, what is the maps that I need to restrict first or all of them? To a novice like me it would sound rather reasonable to only put in a more conservative waste gate duty cycle and keep everything else as is. Thoughts?
#797
EvoM Guru
iTrader: (50)
Thanks mrfred. I'm currently completely stock everything apart from FIC 1150 injectors, modified Wally 255 and a 3" DP with 3-port EBC. So basically I'll keep the MIVEC map as it is once the new exhaust is in, thanks.
A bit off topic, but since it will flow more, what is the maps that I need to restrict first or all of them? To a novice like me it would sound rather reasonable to only put in a more conservative waste gate duty cycle and keep everything else as is. Thoughts?
A bit off topic, but since it will flow more, what is the maps that I need to restrict first or all of them? To a novice like me it would sound rather reasonable to only put in a more conservative waste gate duty cycle and keep everything else as is. Thoughts?
#798
Thank you. I made four different BWGDC maps from material that I had got when I tuned my car with tscomp. I can test these out after I get the exhaust installed and keep an eye on the boost gauge as well as knock and AFR.
This is an EDM edition and therefore the car doesn't have a MAP sensor from the factory nor have I had luck in installing one.
This is an EDM edition and therefore the car doesn't have a MAP sensor from the factory nor have I had luck in installing one.
#802
Help for Ecuflash
Hi:
I using evo 9 wagon 6 speed i try the definitation but it cannot edit the mivec map, what file should i use at rommetadata
can any one pls help
ECU ID:88770005
I using evo 9 wagon 6 speed i try the definitation but it cannot edit the mivec map, what file should i use at rommetadata
can any one pls help
ECU ID:88770005
#803
Newbie
iTrader: (3)
Getting a P0011 code on my 06 EVO IX and thought I would post the MIVEC tables from my tuner here to see if anyone thinks they're off. My builder has gone through timing twice and is about to do it again, tested many mechanical and electrical aspects of the system and even installed a brand new MIVEC gear.
My tuner assures me that the tune is on point and the issue must be mechanical.
Full list of mods if it helps:
GSC S2 Billet 7009s2 cams
GSC Beehive Springs and Retainers part # 5040
FID 1200cc injectors
TOMEI bell mouth 02 housing
TOMEI downpipe
TOMEI titanium test pipe
GReddy full titanium catback
Injen upper & lower inter cooler piping
Injen intake
Grimmspeed electronic boost controller
All gates racing blue belts
ITM revised lifters
Walbro 255 fuel pump
My tuner assures me that the tune is on point and the issue must be mechanical.
Full list of mods if it helps:
GSC S2 Billet 7009s2 cams
GSC Beehive Springs and Retainers part # 5040
FID 1200cc injectors
TOMEI bell mouth 02 housing
TOMEI downpipe
TOMEI titanium test pipe
GReddy full titanium catback
Injen upper & lower inter cooler piping
Injen intake
Grimmspeed electronic boost controller
All gates racing blue belts
ITM revised lifters
Walbro 255 fuel pump