Maf Comp vs Latency question
Jun 10, 2014, 05:34 PM
#47
Evolved Member
Thread Starter
iTrader: (10)
Join Date: Mar 2013
Location: Chicago
Posts: 890
Likes: 0
Received 0 Likes
on
0 Posts
Thanks for the tip, I've always wanted to try the silicone intake as in I heard they work so much better then the steel ones. I like the hps one for the look of it, haha, but I'm pretty sure for performance they're all about equal.
Jun 24, 2014, 02:15 PM
#48
Evolved Member
iTrader: (8)
Join Date: Nov 2010
Location: Georgia
Posts: 752
Likes: 0
Received 0 Likes
on
0 Posts
negative STFT = lower MAF compensation or MAF scaling
Both tables do exactly the same thing. I ended up setting the MAF compensation to all 128 and then retuning the entire MAF scaling table over the entire MAF Hz range. I found this to be the easier way to create a smooth curve with no unintended spikes or steps. Remember that the car needs to be at steady TPS, load, and rpm for a few seconds before the STFT gives an applicable value. And make sure that the LTFTs aren't changing.
Both tables do exactly the same thing. I ended up setting the MAF compensation to all 128 and then retuning the entire MAF scaling table over the entire MAF Hz range. I found this to be the easier way to create a smooth curve with no unintended spikes or steps. Remember that the car needs to be at steady TPS, load, and rpm for a few seconds before the STFT gives an applicable value. And make sure that the LTFTs aren't changing.
for example if the STFT is -8 at given Hz, shoud I lower that value by 8% ?
Jun 26, 2014, 10:34 PM
#50
i'm about 95% done doing this very thing again with a new set of injectors on my own car. my curve was already in pretty good shape, so it took perhaps about four hours of logging, analyzing, and tweaking. definitely helps to have a long steady hill with no traffic. a load bearing dyno would be the hot ticket for getting this done quickly. could probably dial it in at 15 points in about 1 hour.
Jun 27, 2014, 09:39 AM
#53
Evolved Member
Thread Starter
iTrader: (10)
Join Date: Mar 2013
Location: Chicago
Posts: 890
Likes: 0
Received 0 Likes
on
0 Posts
Im running the fic 1100 high z's like you were and I love them. A little loud but I can live with that. I have a self rebuilt 9 turbo with a 20g extended tip billet wheel and a 11.5cm turbine (it was balanced after assembly yes). Im @ 25 psi at 70-80 idc lol so im good for now too but what turbo do you have right now? Again, I'm jw.
Thanks,Jason
Thanks,Jason
Jun 27, 2014, 10:29 AM
#54
Im running the fic 1100 high z's like you were and I love them. A little loud but I can live with that. I have a self rebuilt 9 turbo with a 20g extended tip billet wheel and a 11.5cm turbine (it was balanced after assembly yes). Im @ 25 psi at 70-80 idc lol so im good for now too but what turbo do you have right now? Again, I'm jw.
Thanks,Jason
Thanks,Jason
Jun 27, 2014, 03:00 PM
#57
Evolved Member
Thread Starter
iTrader: (10)
Join Date: Mar 2013
Location: Chicago
Posts: 890
Likes: 0
Received 0 Likes
on
0 Posts
I have my head built to handle that kind of boost but my defi only goes up to 30 so I never tried to tune above 28ish to be safe. Do you have a boost gauge that goes higher then 30????
Jun 27, 2014, 03:52 PM
#59
Evolved Member
Thread Starter
iTrader: (10)
Join Date: Mar 2013
Location: Chicago
Posts: 890
Likes: 0
Received 0 Likes
on
0 Posts
I do have an omni 4 bar set up per your instructions, tyvm 
but a gauge on the dash to monitor that level of boost or no? I know you can data log it but a gauge would be nice.
but a gauge on the dash to monitor that level of boost or no? I know you can data log it but a gauge would be nice.