SD help on evo 8
#1
Evolving Member
Thread Starter
SD help on evo 8
Hi All
I wonder if some one can help me, I'm trying to setup SD on the 260 rom (96530006 originally)? Although the 9652706 roms work fine with the car when I try and switch to the SD roms either the 9653706 and the 9651706 I get the following errors (below) each time I turn the ignition on, also I don't seem to get a temperature valve back. I have the MAP sensor wired into pin 73 and the MAT sensor plugged into the MAF connector (using the SpoolinUp harness). Any help would be appreciated.
I've attached the roms i'm using (on page 2 this post ), they all work and the car runs well with them all, if I clear the dtc's after the car is started with both the SD roms they don't come back, its only if i cycle the ignition.
Can anyone suggest what I need to do to get a temperature reading also?
Thanks
Andy
Diagnostic Codes:Oxygen Sensor
Intake temperature sensor
Throttle position sensor
ISC motor position sensor
Engine coolant temperature sensor
Crankshaft position sensor
Camshaft position sensor
Knock sensor
Injector circuit
Fuel pump relay
EGR sensor
I wonder if some one can help me, I'm trying to setup SD on the 260 rom (96530006 originally)? Although the 9652706 roms work fine with the car when I try and switch to the SD roms either the 9653706 and the 9651706 I get the following errors (below) each time I turn the ignition on, also I don't seem to get a temperature valve back. I have the MAP sensor wired into pin 73 and the MAT sensor plugged into the MAF connector (using the SpoolinUp harness). Any help would be appreciated.
I've attached the roms i'm using (on page 2 this post ), they all work and the car runs well with them all, if I clear the dtc's after the car is started with both the SD roms they don't come back, its only if i cycle the ignition.
Can anyone suggest what I need to do to get a temperature reading also?
Thanks
Andy
Diagnostic Codes:Oxygen Sensor
Intake temperature sensor
Throttle position sensor
ISC motor position sensor
Engine coolant temperature sensor
Crankshaft position sensor
Camshaft position sensor
Knock sensor
Injector circuit
Fuel pump relay
EGR sensor
#2
Evolved Member
iTrader: (30)
I will have to noodle on this for a bit but I would think some of it can be the periphery settings. the rest of it has to be something not entirely compatible. I dont know enough about the EDM cars to know if you can try the 94170015? We can use the EDM, I would surmise you might be able to go backwards and use the US?
aaron
aaron
#3
Evolving Member
Thread Starter
thanks aaron, I've tried it so the bits are the same across the roms that work and the ones that through the errors but no joy. The car is a 260 which I think has the 96530006 rom in it as standard. The 94170715 roms are currently being fixed at the moment
Thanks
Andy
Thanks
Andy
Last edited by And; May 14, 2010 at 12:16 AM.
#4
Evolved Member
iTrader: (5)
Add this table to your rom xml
PHP Code:
<table name="SD Option: IAT Input for MAT - Use 0x03, Fuel Temp ADC_0E for MAT - Use 0x0E" category="Speed Density Programming" address="a821" type="1D" level="1" scaling="Hex8"/>
Might be a similar thing for the MAP sensor but I don't know it off hand sorry
#6
Evolving Member
Thread Starter
i also applied the SD patch to my 96532706 rom and the car does't have the errors anymore but now it is that rich the car won't start, every thing else is the same
Thread
Thread Starter
Forum
Replies
Last Post
scheides
ECU Flash
357
Oct 22, 2021 08:59 AM