Remote Start On 5 Speed

Reply Subscribe

Thread Tools

Search this Thread

Aug 5, 2008 | 12:50 AM

#46

sblvro

EvoM Community Team Leader

iTrader: (2)

Joined: Sep 2001

Posts: 3,135

Likes: 6

From: chicago, michigan, arkansas

Quote:

Originally Posted by johnjonfenomeno

remote start ribbon harness to pin 86 on the relay, pin 85 should go to 12v switched ING.

cut the clutch switch wire in the car one side goes to pin 30 the other to 87a

so when rs is activated the switch will go to 87 closing the circuit one way.. While starting the car normally the switch rests at 87a and pressing the clutch will close the connection.

Does this sound right?

must be right. I installed it almost 2 years ago and don't have the exact readouts/diagram.

Aug 23, 2009 | 12:10 AM

#47

kaj

EvoM Community Team Leader

iTrader: (60)

Joined: Mar 2006

Posts: 13,636

Likes: 824

From: Fresno, CA

i unplugged my BACK clutch sensor. the one that detects FULL CLUTCH ENGAGEMENT. not the front one that detects when the clutch is full OUT.

works great. i don't have the factory 2-step any more.. but i can live with that.

i'm in the process of wiring in a relay to make it work again. cake.

Oct 6, 2009 | 07:15 PM

#48

Chameleonzero

Evolving Member

iTrader: (2)

Joined: Mar 2009

Posts: 135

Likes: 0

From: Jackson, TN

always leave a car in neutral becasue if you are parked on a hill and its in a gear. You can wear you gears out because of the pressure you leave it under

Oct 13, 2009 | 09:05 PM

#49

WRECKLESS96

Newbie

Joined: Aug 2009

Posts: 45

Likes: 0

From: tacoma

the reason everybody is telling you to leave it in neutral is beacuse you will lauch your car down the street or drag it. working in an install bay you always hear stories about manuals with start in them. my buddy started his car into his managers and it lefted his car off of the ground. the rear bumper was almost through the windshield. so just be careful. it can be done. most shops won't do it for that reason. some mom and pop shops will do it but then you have to worry about install quality

Oct 20, 2009 | 10:19 AM

#50

rodent

Evolved Member

iTrader: (35)

Joined: Apr 2006

Posts: 700

Likes: 3

From: Highlands Ranch, CO

Both Viper, Clifford (higher end models) and Compustar have a manual trans mode which means you have to perform a certain sequence getting out of the car. If you leave it in gear and get out the car, it WILL NOT remote start since the alarm knows you did not do the sequence. I have one on my GSX and even though its sometimes a pain getting out to activate it properly, its a fail safe way to do it. Its only on certain alarm models so I'd suggest staying away from doing a cheaper remote start kit and thinking that you'll always leave it in nuetral.

Also, the comment about wearing out the gears by parking in gear is news to me...

Oct 21, 2009 | 06:51 PM

#51

rodent

Evolved Member

iTrader: (35)

Joined: Apr 2006

Posts: 700

Likes: 3

From: Highlands Ranch, CO

This is the one I'm thinking about getting for the Evo.

http://www.viper.com/P-5902V/Viper-5...e-Start-System

http://www.viper.com/Media/ResponderHD.wvx

I'm not sure which Clifford model is the twin as this one but I do have last years Clifford in my GSX and been happy with it. Keep in mind, the mile range is more like 1/8-1/4 mile when it has to go through walls. I found an installer locally that will hook up the remote start on the 5 speed. Most larger shops will not do this even though its totally safe to do. This model sells online for $350 and most installers want $100-$200 for labor.