The Evolution of F-Prepared, Re-build Log.
#136
Evolved Member
iTrader: (2)
If I did my math right, the 46mm restrictor limits you to around 52-53lbs/min mass airflow. That is off the map on the G25-550, and lands you in the 76%-77% compressor efficiency island on the G25-660. Are you going to use the turbo speed sensor to control boost? Are you allowed to run external wastegate dump?
#137
Evolving Member
Thread Starter
Long time no see around these parts. Been a long winter but we are getting the car ready to run for this year. The turbo kit is on, we are building a new oil pan, and the planned suspension upgrades for the year are taking place.
The new SSB Designs prototype 1.25" correction knuckles are being installed. There should be some production units on the way. Unfortunately because of the new placement of the trailing arm attachment, there was significant interference even at full droop with the back of the wheel and the arm. We really don't want to go any wider with the car, so we are opting to build new higher clearance arms.
Between the brakes and the knuckles we are going to shave a minimum of 34lbs. That is not including the ebrake stuff, but since we are putting a staging brake in the car I didn't include it until I weight all those components.
The oil pan will be center sump, with a trap door system around the pickup and a baffle plate around 2/3 the way up the pan. The exhaust will route around the front of the motor, as can be seen by the cutout in the pan.
Sorry for the crappy picture of the brakes.....
Zack
The new SSB Designs prototype 1.25" correction knuckles are being installed. There should be some production units on the way. Unfortunately because of the new placement of the trailing arm attachment, there was significant interference even at full droop with the back of the wheel and the arm. We really don't want to go any wider with the car, so we are opting to build new higher clearance arms.
Between the brakes and the knuckles we are going to shave a minimum of 34lbs. That is not including the ebrake stuff, but since we are putting a staging brake in the car I didn't include it until I weight all those components.
The oil pan will be center sump, with a trap door system around the pickup and a baffle plate around 2/3 the way up the pan. The exhaust will route around the front of the motor, as can be seen by the cutout in the pan.
Sorry for the crappy picture of the brakes.....
Zack
#139
Evolving Member
Thread Starter
Well for some reason I think Flickr is just having a problem loading them, they were there at one point You can see this page never fully loads. Hopefully they will make their way back!
Zack
Zack
#140
EvoM Staff Alumni
iTrader: (3)
Please use EvOMs image host. Cant be any easier!
See here if needed: https://www.evolutionm.net/forums/ev...e-hosting.html
#142
EvoM Guru
iTrader: (1)
Pics work fine on both posts for me.
Looking good Zack, can't wait to see results. Especially from the new turbo setup.
Looking good Zack, can't wait to see results. Especially from the new turbo setup.
#143
Evolved Member
iTrader: (15)
Indeed. Cool to see the rears coming to life. I can't droop much more without significant fender work, may have to borrow your fender idea or fork up for the voltex ones lol. An idea a buddy of mine also gave me is that we need to either nylock or pin the nuts on the ankerman's and on this it looks like a couple other areas. The concern I had with nylocks esp on the front was heat but we'll see. Basically with the vibrations and impacts that's not an area we want to come loose.
#144
EvoM Guru
iTrader: (1)
Indeed. Cool to see the rears coming to life. I can't droop much more without significant fender work, may have to borrow your fender idea or fork up for the voltex ones lol. An idea a buddy of mine also gave me is that we need to either nylock or pin the nuts on the ankerman's and on this it looks like a couple other areas. The concern I had with nylocks esp on the front was heat but we'll see. Basically with the vibrations and impacts that's not an area we want to come loose.
#146
EvoM Guru
iTrader: (1)
Metal-metal stover nuts + red Loctite is far more effective than nyloc nuts.
#149
EvoM Guru
iTrader: (2)
I think I've used red loctite twice in my life. It's meant for bolts that are never supposed to be serviced. Proper procedure to remove bolts with red loctite is to heat them with a torch. If you have to ask yourself if it can handle the heat of a torch it shouldn't have red on it.
Nyloc is plenty IMO.
Nyloc is plenty IMO.