Mark this thread as Unsold
Short Runner TwinScroll manifold/turbine housing/downpipe - GT35r
#1
Short Runner TwinScroll manifold/turbine housing/downpipe - GT35r
Price: $700 shipped(manifold & downpipe only) + shipping for exhaust(if it can be shipped)
Location of seller: Charlotte, NC
Willingness to ship: Cont US
I am selling my old custom short runner twinscroll setup. The setup is in good shape, but definitely DIRTY from sitting around and previous use. Here is a link to my build and dyno results. I was making ~29psi @ 4K rpm in 3rd gear on a built 2L with a GTX3576r.
https://www.evolutionm.net/forums/ev...xperiment.html
This were the results on stock bottom end and the 10:1 2L spooled a bit faster.
https://www.evolutionm.net/forums/ev...0hp-375tq.html
- Custom short runner twinscroll exhaust manifold fabricated by me. Manifold is flanged for twin Tial MV-S 38mm wastegates. Head flange is mild steel and runners are the larger 1.5" (ID 1.682") 304 Stainless Steel Schedule 10 Weld Els. The manifold has an integrated double slip on the longest runner to prevent flange warping.
- ATP 1.06 a/r T4 TS turbine housing cut for a GT35r turbine wheel with v-band clamp. Perfect for a GTX3576r or GTX3582r. It will come with a special tool (shown in picture) that I made for tightening a few of the bolts that are hard to reach with a wrench.
- Custom 3" downpipe with recirculated wastegates and O2 sensor for factory O2 and another for aftermarket O2 behind the engine. Also has fitting welded for exhaust scavenge. This fit my EVO IX with ACD.
- If you want to pay to ship the modified 3" SS ebay exhaust it is yours. I cut off the tip to weld on to my new exhaust, but that is a minor fix. I DON'T KNOW IF THIS CAN BE SHIPPED SINCE IT IS ONE PIECE.
- DOES NOT COME WITH WASTEGATES
I ran this setup from Nov 2011 to March 2013 before swapping to my new custom setup. The setup had no issue and worked very well on my 2L.
WARNING: The flange at the back end of the downpipe is the standard 2 bolt flange with gasket as it started its life as a Greddy downpipe. I modified it to fit my setup along with my 3" SS ebay exhaust. It may be necessary to reposition this flange (cut/weld) to make work with a factory style catback exhaust. It may work, but I cannot verify. It does work with my modified ebay exhaust if you want to have it shipped.
The exhaust on the left (1st picture) is what you can have it you want to pay to ship (if it can be shipped). It has no exhaust tip as shown below on the right (2nd picture), but that is a minor fix and I will weld on a tip if you want to send me one prior to shipping.
Location of seller: Charlotte, NC
Willingness to ship: Cont US
I am selling my old custom short runner twinscroll setup. The setup is in good shape, but definitely DIRTY from sitting around and previous use. Here is a link to my build and dyno results. I was making ~29psi @ 4K rpm in 3rd gear on a built 2L with a GTX3576r.
https://www.evolutionm.net/forums/ev...xperiment.html
This were the results on stock bottom end and the 10:1 2L spooled a bit faster.
https://www.evolutionm.net/forums/ev...0hp-375tq.html
- Custom short runner twinscroll exhaust manifold fabricated by me. Manifold is flanged for twin Tial MV-S 38mm wastegates. Head flange is mild steel and runners are the larger 1.5" (ID 1.682") 304 Stainless Steel Schedule 10 Weld Els. The manifold has an integrated double slip on the longest runner to prevent flange warping.
- ATP 1.06 a/r T4 TS turbine housing cut for a GT35r turbine wheel with v-band clamp. Perfect for a GTX3576r or GTX3582r. It will come with a special tool (shown in picture) that I made for tightening a few of the bolts that are hard to reach with a wrench.
- Custom 3" downpipe with recirculated wastegates and O2 sensor for factory O2 and another for aftermarket O2 behind the engine. Also has fitting welded for exhaust scavenge. This fit my EVO IX with ACD.
- If you want to pay to ship the modified 3" SS ebay exhaust it is yours. I cut off the tip to weld on to my new exhaust, but that is a minor fix. I DON'T KNOW IF THIS CAN BE SHIPPED SINCE IT IS ONE PIECE.
- DOES NOT COME WITH WASTEGATES
I ran this setup from Nov 2011 to March 2013 before swapping to my new custom setup. The setup had no issue and worked very well on my 2L.
WARNING: The flange at the back end of the downpipe is the standard 2 bolt flange with gasket as it started its life as a Greddy downpipe. I modified it to fit my setup along with my 3" SS ebay exhaust. It may be necessary to reposition this flange (cut/weld) to make work with a factory style catback exhaust. It may work, but I cannot verify. It does work with my modified ebay exhaust if you want to have it shipped.
The exhaust on the left (1st picture) is what you can have it you want to pay to ship (if it can be shipped). It has no exhaust tip as shown below on the right (2nd picture), but that is a minor fix and I will weld on a tip if you want to send me one prior to shipping.
Last edited by 240Z TwinTurbo; Mar 18, 2014 at 02:37 PM.
Thread
Thread Starter
Forum
Replies
Last Post
240Z TwinTurbo
Evo Engine / Turbo / Drivetrain
223
Jan 1, 2022 10:44 AM
RUNNING.AMOK
Evo Engine / Turbo / Drivetrain
21
May 24, 2017 04:38 PM
240Z TwinTurbo
Evo Dyno Tuning / Results
15
Nov 9, 2015 03:17 PM
240Z TwinTurbo
Evo Engine / Turbo / Drivetrain
196
Nov 3, 2015 12:29 PM
240Z TwinTurbo
Vendor Service / Parts / Tuning Review
56
May 11, 2015 08:51 PM