AEM Meth Kit - Nozzle Question...
Jun 3, 2008, 02:33 PM
#16
Former Sponsor
iTrader: (9)
Join Date: Nov 2007
Location: Rockford, IL
Posts: 268
Likes: 0
Received 0 Likes
on
0 Posts
The IFS-10 can be installed such that it enables the BBK-10 solenoid to limit boost to WG pressure until your meth starts flowing. Once meth is flowing, the BBK shuts off and allows boost to go up. So no meth, no boost past waste gate.
The IFS has an internal flow meter and monitors the meth flow in real time. It also has an over flow limit in the event a hose is loose.
The AEM uses the same fluid line as our system. Just cut the line from your pump to the nozzle and plug line into the IFS.
The Flow Gauges are an optional device. The IFS outputs a 0-5v signal proportional to flow. Our gauges read this signal and show the flow rate in mL/min.
The IFS has an internal flow meter and monitors the meth flow in real time. It also has an over flow limit in the event a hose is loose.
The AEM uses the same fluid line as our system. Just cut the line from your pump to the nozzle and plug line into the IFS.
The Flow Gauges are an optional device. The IFS outputs a 0-5v signal proportional to flow. Our gauges read this signal and show the flow rate in mL/min.
Jun 4, 2008, 02:17 AM
#17
Evolving Member
Join Date: Nov 2005
Location: Anahiem Hills
Posts: 381
Likes: 0
Received 0 Likes
on
0 Posts
The IFS-10 can be installed such that it enables the BBK-10 solenoid to limit boost to WG pressure until your meth starts flowing. Once meth is flowing, the BBK shuts off and allows boost to go up. So no meth, no boost past waste gate.
The IFS has an internal flow meter and monitors the meth flow in real time. It also has an over flow limit in the event a hose is loose.
The AEM uses the same fluid line as our system. Just cut the line from your pump to the nozzle and plug line into the IFS.
The Flow Gauges are an optional device. The IFS outputs a 0-5v signal proportional to flow. Our gauges read this signal and show the flow rate in mL/min.
The IFS has an internal flow meter and monitors the meth flow in real time. It also has an over flow limit in the event a hose is loose.
The AEM uses the same fluid line as our system. Just cut the line from your pump to the nozzle and plug line into the IFS.
The Flow Gauges are an optional device. The IFS outputs a 0-5v signal proportional to flow. Our gauges read this signal and show the flow rate in mL/min.
Thanks!
Nov 29, 2008, 12:36 PM
#18
Evolved Member
iTrader: (14)
Join Date: Jul 2006
Location: Boynton Beach, Florida
Posts: 2,444
Likes: 0
Received 0 Likes
on
0 Posts
im going to bump this thread. im running the largest meth nozzle on the AEM kit and would like to run a bigger nozzle. anyone help me out finding a new nozzle? or should i run a splitter and 2 nozzles?
Thread
Thread Starter
Forum
Replies
Last Post
besk
Water / Methanol Injection / Nitrous Oxide
5
May 21, 2014 10:15 AM
EVIL-EVO-8
Water / Methanol Injection / Nitrous Oxide
9
Jun 14, 2009 06:45 PM
wreckleford
Water / Methanol Injection / Nitrous Oxide
1
Sep 26, 2008 09:14 PM
Blue Evo 8
Evo Engine / Turbo / Drivetrain
27
Jul 12, 2006 02:03 PM
