AEM inline controller serial logging
#1
Newbie
Thread Starter
Join Date: Sep 2010
Location: Iowa
Posts: 63
Likes: 0
Received 0 Likes
on
0 Posts
AEM inline controller serial logging
My com 1 is enabled, I am going straight to serial port, my controller is wired correctly, I have made sure i am on the correct pins in the dsub, My green light is solid, but I can not for the life of me get it to work with ATR. Plus the ATR crashes almost every time I try to get the dashboard up. Anyone have any ideas?
#3
Newbie
Thread Starter
Join Date: Sep 2010
Location: Iowa
Posts: 63
Likes: 0
Received 0 Likes
on
0 Posts
How does hyperterminal work? What should I see? I set up a new connection through the com1 port and it just goes to a black screen with the flashing courser. I have been reading about a lot of frustration, but I am connected correctly on the gauge side. I have no manual dealing with troubleshooting for this unit. Thanks in advance!!
#5
Newbie
Thread Starter
Join Date: Sep 2010
Location: Iowa
Posts: 63
Likes: 0
Received 0 Likes
on
0 Posts
Man! I get nothing. I got a solid green light on the inline controller, I have ran a jumper ground wire to the battery. I have the gray wire soldered to pin 2 and the ground soldered to pin 5 of the serial connector. My com port works as I use it for an LCD projector. I am using xp, with ATR. I guess im down to the sensor itself??
#7
Newbie
Thread Starter
Join Date: Sep 2010
Location: Iowa
Posts: 63
Likes: 0
Received 0 Likes
on
0 Posts
I am using com 1, dont know how to set it up any more than making sure it's enabled which it is.
I double checked all connections, ran jumper leads to the battery, green light on the controller is on but I have only seen the red light flash one time. (was told this was the heater circuit) I have looked over all my wiring, made sure the sensor was plugged in and seated in the connector all the way.
When I try to use hyperterminal, it just shows up as jumbled symbols. I unplug the serial connector and they stop so I am assuming its picking up something maybe not?!? I am using accesstuner race software and both on the dashboard and in the log file all that shows up is 0.00 constantly. I am down to pulling the sensor and or trying to get some sort of warranty? which i doubt AEM or MAP will do.
Inputs from anyone would be appreciated, I usually am able to figure this out, but this one has me totally stumped.
I double checked all connections, ran jumper leads to the battery, green light on the controller is on but I have only seen the red light flash one time. (was told this was the heater circuit) I have looked over all my wiring, made sure the sensor was plugged in and seated in the connector all the way.
When I try to use hyperterminal, it just shows up as jumbled symbols. I unplug the serial connector and they stop so I am assuming its picking up something maybe not?!? I am using accesstuner race software and both on the dashboard and in the log file all that shows up is 0.00 constantly. I am down to pulling the sensor and or trying to get some sort of warranty? which i doubt AEM or MAP will do.
Inputs from anyone would be appreciated, I usually am able to figure this out, but this one has me totally stumped.
Last edited by iowa_guy; Oct 30, 2011 at 06:54 PM.
Trending Topics
#9
EvoM Community Team
iTrader: (15)
-----
Also, please note that there is a thread that looks quite a bit like yours (despite ATR vs Evoscan) and a few other, very related posts:
https://www.evolutionm.net/forums/ev...d-evoscan.html
https://www.evolutionm.net/forums/ev...headaches.html
-----
OH, and your threads. Please don't clutter up the forum if you can help it:
https://www.evolutionm.net/forums/co...headaches.html
https://www.evolutionm.net/forums/ev...l-logging.html
Thread
Thread Starter
Forum
Replies
Last Post
jmoney2001
Cobb AccessPORT
0
Oct 6, 2016 10:28 AM
gtm_maxwell
Cobb AccessPORT
1
Sep 19, 2016 12:45 PM
iowa_guy
Cobb AccessPORT
7
Sep 28, 2012 08:11 PM
Octane Blue
Evo X Engine Management / Tuning Forums
2
Sep 30, 2010 09:44 AM