Which 02 housing won't cause creep?
Thread Starter
Evolving Member
iTrader: (6)
Joined: Jul 2006
Posts: 172
Likes: 3
From: Poughkeespie NY
Which 02 housing won't cause creep?
Don't care which one has the most power, just looking for one that is less prone to boost creep. I was looking at map 02, jmf,indivia, BR, or just stock one ported. Anyone have luck with any of these? I know I could go with a dump but I don't want one.
Thanks
Thanks
Thread Starter
Evolving Member
iTrader: (6)
Joined: Jul 2006
Posts: 172
Likes: 3
From: Poughkeespie NY
I think toxic fab was going to produce one. you should contact him. if i ever deviate from stock I will probably try him first.
Here is a pic of one of his: https://www.evolutionm.net/forums/ev...on-pics-8.html
Hopefully it will meet the following criteria as mentioned by another member
https://www.evolutionm.net/forums/se...ml#post7906463
Here is a pic of one of his: https://www.evolutionm.net/forums/ev...on-pics-8.html
Hopefully it will meet the following criteria as mentioned by another member
https://www.evolutionm.net/forums/se...ml#post7906463
Originally Posted by funks
I'm not gone - lol. I simply won't buy an O2 housing that doesn't have the support tab, IMHO - Mitsu put it there for a reason. Without it, the manifold is bearing all the weight (turbo + exhaust), my assumption is that it helps when the engine is moving around (during acceleration and such).
It's too bad the INVIDIA has it's o2 sensor located in the wrong spot (it does have the support tab though), and the WORKS costs so much you'd have to sell a kidney for one (it only works with their downpipe), nevertheless - it's out of topic now. Thanks for trying to see if it's feasible cost wise though. If you guys ever decide to make a non-dump O2 housing, coated, and the support tab in place, definitely interested (a plus too if it has support for the stock heat shield).
I'm not gone - lol. I simply won't buy an O2 housing that doesn't have the support tab, IMHO - Mitsu put it there for a reason. Without it, the manifold is bearing all the weight (turbo + exhaust), my assumption is that it helps when the engine is moving around (during acceleration and such).
It's too bad the INVIDIA has it's o2 sensor located in the wrong spot (it does have the support tab though), and the WORKS costs so much you'd have to sell a kidney for one (it only works with their downpipe), nevertheless - it's out of topic now. Thanks for trying to see if it's feasible cost wise though. If you guys ever decide to make a non-dump O2 housing, coated, and the support tab in place, definitely interested (a plus too if it has support for the stock heat shield).
Last edited by icrnk; Dec 29, 2010 at 08:24 AM.
Trending Topics
I have zero boost creep with my ebay ss ported o2 housing and its getting the job done as im making power boss. I also had it coated by the beset in the business TiradoCustomCoatings. pmed
coated
coated
Last edited by RockmanX; Dec 29, 2010 at 10:39 AM.
nope they sell them in ported or non ported versions. You can send it off to any good shop and port it out if you want just dont take to much out or leave it alone and just coat it
you can not port a megan o2 housing, but you can clean the weld spots a little. Megan is so far the most proven o2 housing ( comparing it from the best bang for the back point of view). None of the aftermarket o2 housing creep, it just depends what you are wiling to pay for. I dont think the oem creeps either....thats where twin scroll set up comes in handy
Thread
Thread Starter
Forum
Replies
Last Post
Evol2004
Evo Engine / Turbo / Drivetrain
4
Feb 16, 2017 04:23 PM
svt_lightning01
Evo General
10
Mar 31, 2011 01:08 PM
nitz
Evo X Engine / Turbo / Drivetrain
8
Aug 12, 2009 08:17 AM
Nissan2Evo
ExtremeTurboSystems.com – WA
9
Feb 25, 2008 08:55 AM
