Air spoiler ( Tall Wing) Evo X
Sep 15, 2009, 11:52 AM
#49
Evolving Member
Thread Starter
iTrader: (8)
Join Date: Feb 2005
Location: miami, fl
Posts: 161
Likes: 0
Received 0 Likes
on
0 Posts
you need to do just one hole inside the trunk has the mark where.
I don't do the hole under the cap and is just fine.
the placement of the poinst for installation are the same just one needs to be drilled and as i said before the one under the cape needs like a grommet with thread to install the screw so i dont do it.
I don't do the hole under the cap and is just fine.
the placement of the poinst for installation are the same just one needs to be drilled and as i said before the one under the cape needs like a grommet with thread to install the screw so i dont do it.
Last edited by nelsondevicenci; Sep 15, 2009 at 11:54 AM.
Sep 15, 2009, 12:42 PM
#50
Evolved Member
iTrader: (7)
Join Date: May 2008
Location: Los Angeles
Posts: 565
Likes: 0
Received 0 Likes
on
0 Posts
I've been looking at how to improve my stock GSR wing for awhile now and I haven't been able to locate anything solid. The one upgrade that I've seen that I could potentially benefit from is the AMS Wickerbill that they made for Ryan on his X. I attached a photo of it below, I hope Ryan won't mind me linking his pics.
I've contacted AMS around a week ago but I still haven't gotten a response.
I've contacted AMS around a week ago but I still haven't gotten a response.
Sep 16, 2009, 12:04 PM
#52
Evolved Member
iTrader: (12)
Join Date: Feb 2005
Location: Pewaukee, WI
Posts: 606
Likes: 0
Received 0 Likes
on
0 Posts
you need to do just one hole inside the trunk has the mark where.
I don't do the hole under the cap and is just fine.
the placement of the poinst for installation are the same just one needs to be drilled and as i said before the one under the cape needs like a grommet with thread to install the screw so i dont do it.
I don't do the hole under the cap and is just fine.
the placement of the poinst for installation are the same just one needs to be drilled and as i said before the one under the cape needs like a grommet with thread to install the screw so i dont do it.
The GTS actually looks close enough to the X and RA that I regularly get them confused when driving. I bet the wing looks nice on it. I'm enjoying the stealth wingless look myself, so I guess I'm trying to make my Evo into a GTS
. Take it easy 
.
Last edited by Tractionlimit; Sep 16, 2009 at 12:12 PM.
Mar 23, 2010, 11:55 AM
#55
Newbie
iTrader: (1)
Join Date: Feb 2010
Location: SCV
Posts: 52
Likes: 0
Received 0 Likes
on
0 Posts
well i just got my high wing installed. we used all three screws on both sides, becasue at speeds of 140mph plus im not sure if i trust just two bolts, looks great, install was pretty easy too.
Dec 15, 2010, 07:00 AM
#56
Newbie
iTrader: (5)
Join Date: Dec 2003
Location: Las Colinas, TX
Posts: 71
Likes: 0
Received 0 Likes
on
0 Posts
Anyone have any more advice on the install? Most of the pics are dead and there doesn't seem to be a lot of detailed information (drill bit size, hardware needed, what to remove, etc). I am going from an SE deck lid with no holes to a SSS tall wing.
Thread
Thread Starter
Forum
Replies
Last Post
