EVO 11.5 Hotside, anybody try it?

Reply Subscribe

Thread Tools

Search this Thread

Jun 28, 2011 | 03:30 AM

#166

EvolutionEst

Newbie

iTrader: (1)

Joined: Dec 2006

Posts: 46

Likes: 0

From: Tallinn, Estonia

Does anyone know if the TD06 Green version would fit the older FP Green turbo without machining?

Jun 28, 2011 | 10:44 AM

#167

D Grade

Evolving Member

iTrader: (27)

Joined: Sep 2008

Posts: 271

Likes: 0

From: Tucson, AZ

Quote:

Originally Posted by sparky

Have you already installed the FP anti-surge cover? If so, what is your assessment so far? Do you plan on switching over to S.D. as well?

I have the 84mm FP comp cover and love it, probably one of the best bolt on bang for the buck parts out there right now. The stock IX turbo is spooling faster and hitting super hard with less lag between shifts. On top of that it just sounds plain wicked. I dyno'd one week before install and put down 431whp 378ft/lbs on 30psi, E85, SD, stock mivec engine and stock ix turbo unported. A week later I put down only 414whp after the compressor cover and 4" intake on different dyno jet with crappy dyno conditions. Theres no way I lost 17whp with an obvious improvement, my butt dyno tells me way different. I was going to do a writeup, but due to the results of the last dyno, its going to have to wait till Im able to head back down to ER on the same dyno and similar conditions to the 431 pull.

Quote:

Originally Posted by wshihdnevo

I would love to have a Magnus V5 or a Wilson Ported Manifold but the Magnus I have is a the V2 raised Velocity stacks Magnus street SMIM. My last outing last July I made 385 so I am hoping to better that before I throw the 11.5cm housing on. I think I am going to order it up on Monday.

Youre gonna make some silly numbers, cant wait to see the results. Sell me 100% on this housing.

Jun 28, 2011 | 10:56 AM

#168

06MREvo

Evolved Member

iTrader: (90)

Joined: Nov 2005

Posts: 4,800

Likes: 6

From: Raleigh, NC

Quote:

Originally Posted by wshihdnevo

Also ordered up the same O2 housing as RJSP. Im going to make sure the outlet is ported to 3" and it will go on with the 11.5cm housing at the same time.

Nice! Looking forward to results sir!

Jun 28, 2011 | 12:01 PM

#169

wshihdnevo

Evolved Member

iTrader: (88)

Joined: Dec 2006

Posts: 2,765

Likes: 1

From: Tacoma

Quote:

Originally Posted by D Grade

Youre gonna make some silly numbers, cant wait to see the results. Sell me 100% on this housing.

I hope so! At least not lose any power is the plan...

Quote:

Originally Posted by 06MREvo

Nice! Looking forward to results sir!

Me too!

Jun 29, 2011 | 05:26 PM

#170

211Ratsbud

EvoM Guru

iTrader: (1)

Joined: Oct 2010

Posts: 4,286

Likes: 43

From: Watertown, NY

Fail. As I was installing my fap cover, my turbo told me it was in need of a rebuild. So my 10.5 housing is cracked. And I will replace it..

Jun 29, 2011 | 05:34 PM

#171

211Ratsbud

EvoM Guru

iTrader: (1)

Joined: Oct 2010

Posts: 4,286

Likes: 43

From: Watertown, NY

Of what material is this constructed of? Iron or steel? Robert at fp pointed out to me that oe is cast steel and this is likely a cast iron product ..??lifespan ftl

Jun 30, 2011 | 12:00 PM

#172

D Grade

Evolving Member

iTrader: (27)

Joined: Sep 2008

Posts: 271

Likes: 0

From: Tucson, AZ

Cast usually has a good life span and good heat retention, but adds weight and lacks in the bling department. Im assuming its the same as OEM cast or possibly high nickel cast which is less fun to port.

Jun 30, 2011 | 04:02 PM

#173

wshihdnevo

Evolved Member

iTrader: (88)

Joined: Dec 2006

Posts: 2,765

Likes: 1

From: Tacoma

Got this today, quality is pretty spot on, just got to port out the outlet to a true 3":

The housing was out of stock so they drop shipped it to me from the vendor, which was nice of them!

I should see the housing prob by Tuesday and will post up pics!

Jun 30, 2011 | 04:04 PM

#174

Guerillah

Evolved Member

iTrader: (10)

Joined: Jun 2004

Posts: 760

Likes: 1

From: Tucson, AZ

Thanks for the pics !

Jun 30, 2011 | 04:19 PM

#175

mrfred

EvoM Guru

iTrader: (50)

Joined: Mar 2006

Posts: 9,675

Likes: 132

From: Tri-Cities, WA // Portland, OR

Quote:

Originally Posted by wshihdnevo

Got this today, quality is pretty spot on, just got to port out the outlet to a true 3":

...

The housing was out of stock so they drop shipped it to me from the vendor, which was nice of them!

I should see the housing prob by Tuesday and will post up pics!

Is it the Titek v2?

Jun 30, 2011 | 04:27 PM

#176

Aby@MIL.SPEC

Former Sponsor

iTrader: (161)

Joined: Jun 2003

Posts: 3,043

Likes: 13

From: San Elijo Hills, Ca.

Nice o2 housing.

details please....brand, cost, where did you get it?

Jun 30, 2011 | 04:32 PM

#177

wshihdnevo

Evolved Member

iTrader: (88)

Joined: Dec 2006

Posts: 2,765

Likes: 1

From: Tacoma

Quote:

Originally Posted by Aby@MIL.SPEC

Nice o2 housing.

details please....brand, cost, where did you get it?

Quote:

Originally Posted by mrfred

Is it the Titek v2?

http://cgi.ebay.com/ebaymotors/ws/eB...K%3AMEWNX%3AIT

Jun 30, 2011 | 05:26 PM

#178

RazorLab

EvoM Guru

iTrader: (8)

Joined: Aug 2003

Posts: 14,094

Likes: 1,092

From: Mid-Hudson, NY

Looks exactly the same as TitekV2. The only difference is the outlet is flat where the titek has a piece sticking out.

Jun 30, 2011 | 05:59 PM

#179

wshihdnevo

Evolved Member

iTrader: (88)

Joined: Dec 2006

Posts: 2,765

Likes: 1

From: Tacoma

Yeah its from the same vendor Im assuming. Just with a bigger 2.8" outlet and a flat flange like the dsm's are. The sole reason I bought it is b/c its 3" O/D

Jun 30, 2011 | 07:38 PM

#180

211Ratsbud

EvoM Guru

iTrader: (1)

Joined: Oct 2010

Posts: 4,286

Likes: 43

From: Watertown, NY

Looks similar to the map version