mitsuorder's 4g69 experiment
Newbie
Joined: Jul 2006
Posts: 42
Likes: 0
From: 757 VA
I sold the 100mm crank and put in a 94mm stroke, 10.5 compression ratio http://facebook.com/4g69evo
I sold the 100mm crank and put in a 94mm stroke, 10.5 compression ratio http://facebook.com/4g69evo
Cool car I've seen it before on Youtube
. Happy to see its doing well
Newbie
Joined: Jul 2006
Posts: 42
Likes: 0
From: 757 VA
Newbie
Joined: Apr 2019
Posts: 14
Likes: 0
From: Queensland
This is a very inspiring thread despite it being a few years old i'm going to use it for reference in doing an evo head swap onto my 4g69 in my 2006 CH Vrx (Ralliart overseas) Lancer Sedan as well as converting it to AWD it'll be a few years to be able to complete it but I have a base outline of where I want to head with it, aiming for a balance of performance and reliability as it'll be my daily driver as well and also be a fun track car. If there's anything I should know that would be greatly appreciated and also if I should go outlander AWD or Evo AWD.
Cheers from Australia
Cheers from Australia
Newbie
Joined: Sep 2008
Posts: 8
Likes: 0
From: not important.
Let me start this off with the fact that this is an experiment. I began with wanting to push the Evolution IX Mivec head/4g69 block combo to the limits so as to provide information on a potential option to the community. Huge advocate of sharing information, the good, the bad, the ugly. Hiding it does nothing for any of us.
With that said here is my 6466 4g69 build. Heading out of the country in October for a while so wrapping it all up this month. It is not running yet but everything is here. Been a lot of planning, looking at what was available, and simply wanting to do things right. Least competitive person you'll ever meet so check the machismo neanderthal stuff at the door please
I will be updating this and answering any question to be had. Have held off on putting it all up as I didn't want to lead anyone in the wrong direction since nothing has fired, run, or blown up as of yet haha. But seriously though guys, this is an experiment. I did it because I wanted to see what would happen with this iron block if you pushed it with a build that has had no real limit, within reason, or deadline. So here are the pics.
mitsuorder
With that said here is my 6466 4g69 build. Heading out of the country in October for a while so wrapping it all up this month. It is not running yet but everything is here. Been a lot of planning, looking at what was available, and simply wanting to do things right. Least competitive person you'll ever meet so check the machismo neanderthal stuff at the door please
I will be updating this and answering any question to be had. Have held off on putting it all up as I didn't want to lead anyone in the wrong direction since nothing has fired, run, or blown up as of yet haha. But seriously though guys, this is an experiment. I did it because I wanted to see what would happen with this iron block if you pushed it with a build that has had no real limit, within reason, or deadline. So here are the pics.
mitsuorder
Also hypothetically, can this be done with an older head from say, a 6 or 7?
Newbie
Joined: Sep 2008
Posts: 8
Likes: 0
From: not important.
all the Evo accessory water pump, timing. will directly bolt-on. this box is the exact deck height as 63. the reason it som differences is because the desk height is different and the water pump is aswell
Thread
Thread Starter
Forum
Replies
Last Post
TommiM
Evo Engine / Turbo / Drivetrain
410
May 26, 2022 08:41 AM
mclaren
Evo How Tos / Installations
21
Aug 1, 2016 06:24 PM
billyboy1
09+ Ralliart Show and Shine
169
Feb 25, 2016 10:28 PM
