Virtual Dyno Room-Dyno Simulator
First, you need to lookup the gear ratios for your particular transmission model # f5m42 (most likely online or in a haynes service manual perhaps). It appears that 3rd gear= 1.379, 4th gear=1.030, and the final drive gear=3.722
If you did a 3rd gear pull, find the gear ratio for 3rd gear and for your FINAL DRIVE gear. Enter those values on the page where you select your tire diameter.
On the dyno page, for transmission type selecet the USER option. This makes the simulator use the gear ratios you manually entered on the other page. The drag coefficient won't be the same since right now its only set for an evo 8/9 but it will get you a ballpark figure.
If you did a 3rd gear pull, find the gear ratio for 3rd gear and for your FINAL DRIVE gear. Enter those values on the page where you select your tire diameter.
On the dyno page, for transmission type selecet the USER option. This makes the simulator use the gear ratios you manually entered on the other page. The drag coefficient won't be the same since right now its only set for an evo 8/9 but it will get you a ballpark figure.
Just choose any transmission on the list, the USER selection is in the 'GEAR' box....sorry, my bad. Once you select the USER option, its using the specific gear ratios you entered manually so transmission type is over-riden.
the dyno sim says i have 269hp & 346tq. How close to my real hp & tq is it? i know its impossible to know for sure until i get on a real dyno, but i put in everything from the weight of the car an me to the 3rd gear an final gear ratios.
Account Disabled
iTrader: (38)
Joined: Aug 2005
Posts: 9,319
Likes: 1
From: Virginia Beach, Virginia
what dynojet data did you need in particular? https://www.evolutionm.net/forums/ev...ld-record.html
Registered User
Joined: Nov 2007
Posts: 1,507
Likes: 2
From: Trinidad
sorry for my ignorance, is V5.6 the latest simulator? i know there was an issue with the gearing ratios for the IX 6 speed G-Box?
also the download link is not working
also the download link is not working
Last edited by rolly1818; Aug 26, 2009 at 04:34 AM.
what dynojet data did you need in particular? https://www.evolutionm.net/forums/ev...ld-record.html
I believe the gearing issue was fixed, although v5.6 still has plenty of bugs. Since we are working on a full stand-alone program now, the revisions are on hold until the new stand-alone version is released. Link works fine for me over here *shrug*
Last edited by Jack_of_Trades; Aug 26, 2009 at 06:16 AM.
Account Disabled
iTrader: (38)
Joined: Aug 2005
Posts: 9,319
Likes: 1
From: Virginia Beach, Virginia
ok, I'm sending Ryan one of the dyno owners an email right now about this. It is a Dynojet.
Account Disabled
iTrader: (38)
Joined: Aug 2005
Posts: 9,319
Likes: 1
From: Virginia Beach, Virginia
I ran out of e85 and my ebc is pegged so Kevin is going to borrow the truck and we'll go get 55gal more e85 and he's going to let me borrow his MBC to see if we can get it in the 43psi area. Once the tune is checked at that level we should be ready for the track.
Registered User
Joined: Nov 2007
Posts: 1,507
Likes: 2
From: Trinidad
I believe the gearing issue was fixed, although v5.6 still has plenty of bugs. Since we are working on a full stand-alone program now, the revisions are on hold until the new stand-alone version is released. Link works fine for me over here *shrug*
OpenSource FTW! lol
Registered User
Joined: Nov 2007
Posts: 1,507
Likes: 2
From: Trinidad
The guy working on it (bbarnhill) was hoping to send me a beta version to check out this week so hopefully sooner than later. I'm excited to see where we can take this OpenSource FTW! lol
